my “OIL CHANGE REQUIRED” notice keeps appearing on my das...


my “OIL CHANGE REQUIRED” notice keeps appearing on my dashboard screen, why is this? ...

my “OIL CHANGE REQUIRED” notice keeps appearing on my dashboard screen, why is this?

Automotive Expert
Hi and thank you for using JustAnswer. The oil change required notice will come up if it wasn't reset during the last oil change or if it is actually time for an oil change. Here's the reset procedure to turn it off: Only reset the oil life monitoring system after changing the [engine oil and oil filter](https://my.alldata.com/repair/#/repair/vehicle/56791/component/484/filter/). 1. Switch the ignition on. Do not start the engine. For vehicles with push-button start, press and hold the start button for two seconds without pressing the brake pedal. Do not start the engine. 2. Press the accelerator and brake pedals at the same time. 3. Keep the accelerator and brake pedals fully pressed. 4. After three seconds, a message confirming that the reset is in progress will be displayed. 5. After 25 seconds, a message confirming that the reset is complete will be displayed. 6. Release the accelerator and brake pedals. 7. The message confirming that the reset is complete will no longer be displayed. 8. Switch the ignition off. For vehicles with push-button start, press the start button to switch the ignition off.

What others are asking

Not getting fire to plugs
Hello, being that you had a blown fuse for the starter and replaced the fuse and starter, I will assume that it cranks over now. For the lack of spark, did you check all your fuses. You could also have...
My passenger window goes down but not up.
Windows motors are designed to move in both directions and if you operate the motor in both directions and hear the noise inside the door like a grinding noise, then you have a bad window regulator (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-window-motor-regulator-assembly). It is possible...
Fuel pump not working 1997 Suzuki Esteem
The problem may not be a fuel-related issue but spark or timing. If the engine speed sensor (https://www.yourmechanic.com/services/speed-sensor-replacement) is failing and the computer cannot determine, which cylinder to fire the vehicle will not start. These sensors can often fail intermittently...
Check Engine Light is on and I am getting codes P2600, P22aa, and P24aa
Hello. The codes you have provided are related to the engine and emissions systems. P2600 (https://www.yourmechanic.com/article/p2600-obd-ii-trouble-code-coolant-pump-control-circuit-open-by-brady-klopfer) appears to be related to an issue with the engine's coolant pump circuit. This model of vehicle uses an electric water pump. The computer...
I was driving my 2013 Nissan Altima 5 miles or less. When I threw it in Park I heard a noise.
Hello - most likely the neutral safety switch, or its circuit, are malfunctioning. If your dome light also no longer works, there will be a blown fuse that also keeps your neutral safety switch from working. I would recommend having...
fuel leak under hood
Hi there: Without being there to physically inspect your Mazda, it's impossible for us to tell you what is causing your fuel leak. If it's with the fuel rail however, you should take the time to replace the entire rail,...
The check engine, Trac off and Vsc light came on my car. The code that came up is P0446 (Evap System Vent Control Fault).
Hi there. That light is not going away until the fault has been properly diagnosed. The code may or may not be the same. The code that is stored is a guide for a qualified technician to use. It does...
What would cause my security light to come on in my 1994 Oldsmobile Cutlass
Hello. Most of the time this is caused by a failure in the key sensor located inside of the key lock cylinder. Either the sensor itself fails or the wiring from the sensor located in the steering column fails. Most...
Car keeps burning out ignition coil, same spot, not spark plug.
Hello There, I would suggest checking the ignition control module. The ignition control module functions in two modes; the start and run modes. When starting the engine, the ignition control module allows full battery voltage to be deployed to the...