☰
GET A QUOTE

Hello. I replaced the crankshaft position sensor on my do...


Hello. I replaced the crankshaft position sensor on my dodge avenger and now it won't start. Mechanic's Assistant: Does the vehicle stall at low speeds? Does it sputter? It was before I changed out the sensor. The rpm nee...

Hello. I replaced the crankshaft position sensor on my dodge avenger and now it won't start. Mechanic's Assistant: Does the vehicle stall at low speeds? Does it sputter? It was before I changed out the sensor. The rpm needle would drop to zero Mechanic's Assistant: What year is your Avenger? 2014 Mechanic's Assistant: Are you fixing your Avenger yourself? What have you tried so far? Attempting too. Plugged the computer tool into it, it said crankshaft position sensor. So I changed that That's it so far Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? No that's it

Read More

Responses

Automotive Expert
Hello, my name is \*\*\*\*\* \*\*\*\*\* to just answer! I will be assisting you with all of your vehicle questions today. I’m really sorry that you’re having this issue and I’m going to help you through it, but please understand that I (respectfully) don't know your skill level or tools you have to assist us to diagnose/repair your vehicle. Also, understand that I can't see, smell, hear or touch the vehicle either, so your patience/understanding is appreciated. I do not know anything about the fees or charge so please if you have any concerns, direct them to customer service. The site will prompt you for a phone call. **Ignore the pop-ups.** I will let you know if one is needed. Thank you.

Thanks David. I appreciate any help or input. I am not professional nor do have big fancy tools. Best I got is an air compressor with impact tools.
Automotive Expert
ok is the rpm needle moving up at all when cranking the engine now?

Sometimes but then goes back to zero
Automotive Expert
did you replace it with an aftermarket part or an OEM part?

Aftermarket
Automotive Expert
**do you still have a crankshaft position sensor fault code?**
Automotive Expert
ok, P0335?

Yeah
Automotive Expert
what size engine is in that?

2.4
Automotive Expert
ok, standby for a few check for 5 volts on the pink yellow wire on the crankshaft position sensor connector

I see a green. No pink or yellow
Automotive Expert
2014 dodge avenger 2.4 correct?
Automotive Expert
here's the schematic (attached)

I see it. Does this reset the computer?
Automotive Expert
what do you mean does it reset the computer?

I dunno
Automotive Expert
please check the pink /yellow wire for 5 volts. remove the connector and check for 5 volts
Automotive Expert
Thank you for letting me know you no longer need help. I want to make sure you are taken care of. But with no response, I can only give you what I already have. Have a great day. If you need to continue or if there is anything else I can assist with at all, let me know here and I will be happy to assist further!

Still not sure what you need?

Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.

Get a Diagnostic

Top Questions

Trending Topics

What others are asking

A.I.R. pump whistling
The air injection pump is the most common failure of the air injection system on this vehicle. The system would need to be checked to make sure the pump is the cause of the noise. I recommend you have a...
Read more
Recommendation on buying a Subaru--Impreza STI or a WRX
I'd go for the STI if I were you. And, like I've said many times--if you are getting a Subaru get a standard transmission. Their automatic transmissions stink. They are horrible. They wear out. They cost a fortune to fix....
Read more
Vent system malfunction
It is highly unlikely that these two issues are related. The issue you are likely having is that the mode door actuator has failed. The mode door actuator controls the mode door which will move in different directions to block...
Read more
04 dodge Durango, 3.7 just changed engine,battery,and starter. Still won't crank over, getting power to solenoid,when key is turne
The most important thing to understand about electricity is it occurs on the atomic level. What appears to be a good connection to the human eye may not be to electricity. This is why we have test lights and multimeters...
Read more
It threw a code 21 , throttle position sensor bad code. i replaced it and the code went away but i still have no spark.
Hello and thank you for contacting YourMechanic. The problems that you are encountering with your vehicle, could be caused by the harness to the Throttle Position Sensor (TPS) or the computer itself. Check the harness to the TPS for any...
Read more
What qualifications do you need if you are to rebuild an engine?
Hi there. If you were to rebuild an engine on your own in your garage (that is, your engine and not someone else's engine), you would just need your tools and some books (with procedures and specifications) that can help...
Read more
My car has a high or surging idle
Hi there: The throttle position sensor is the most common component that causes similar idle issues you're experiencing, so it makes sense that replacing the TPS (https://www.yourmechanic.com/services/throttle-position-sensor-replacement) might be a good start. However, other issues could include dirty throttle body...
Read more
Not getting good read on my oil dipstick
Hi There, The best time to check the engine oil is usually just before starting the motor or after it has been shut down for 10-20 minutes. This allows for all of the oil in the motor to be drained...
Read more
When you turn on the ignition a couple of lights come on but it won't start
Confirm that the "new" battery is actually fully charged. Even if the immobilizer were set at one point or it activated, simply arming and disarming it, via the key FOB or remote, will disable the alarm. There is no "lock...
Read more

Browse other content

Estimates
Cars
Services
Maintenance