Showing articles & questions for topic
STS

Check the fluid level to be sure it is not either too high or too low. If the fluid level is correct, the high temperature is due to a malfunction such as a slipping clutch or band. That, in turn...

I'm not sure why you are getting the definition of "throttle body filter" for the code P0068. The definition I come up with is throttle body air flow performance. In fact, all of your codes are having to do with...

You may have a clogged filter and should try having a transmission filter change and fluid replaced to see if it fixed the problem first before having the transmission further diagnosis done.

It could be that the battery in the key fob is weak. The key fob uses a watch battery and it lasts a long time, but won't go on forever. The batteries are usually standard items that you can buy...

Transmission fluid and condition can cause the transmission temperature to rise. The transmission relies on the fluid not only for hydraulic pressure to move the vehicle and change gears, but relies on it for cooling as well. Low fluid level...

Hi there. Typically this warning light issue is associated with the inability to start the car as well. The way this code is reset in that case is to turn the key in the accessory switch location (first click that...

Hi there. When the computer says that the bank 1 or bank 2 is lean, it is referring that the cylinders do not have enough fuel to burn. Check the injectors (https://www.yourmechanic.com/services/fuel-injector-replacement) and see if they are plugged up. Look...

On this vehicle the upper control arm to knuckle retaining nut must be removed. Using SST (special service tool) J 43631 (or equivalent) the upper control arm is separated from the knuckle. After the hub/bearing assembly bolts are removed, typically...

Hey there, thanks for writing in. In the future, please include the code number. There are several codes that this system can set. If you have a crank sensor code, this will cause your car to not start. The most...

Hello, thanks for writing in. I'd be happy to help. I would like to know if the engine is cranking over or if nothing happens. If it is cranking and not starting, then that is usually caused by a bad...

Code P0068 can have to do with the Throttle Position Sensor (https://www.yourmechanic.com/services/throttle-position-sensor-replacement). It can also be due to a Mass Air Flow sensor fault (https://www.yourmechanic.com/services/mass-airflow-sensor-replacement). Usually this code can be set due to a vacuum leak, either somewhere in the...

Coolant leaks are a common failure point for many vehicles. The most likely cause of a coolant leak is due to one of the heater hoses, radiator hose (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-radiator-hose), water pump (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-water-pump), radiator (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-radiator), or a coolant tank (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-coolant-reservoir). Leaks...

Claimed by Kevin Gainer

Hi Ken. Thanks for contacting us tonight. What you are describing is commonly caused by an open or damaged electrical relay that operates the power lock function on your door. When the relay is stuck in an open position, it...

Your car has 4 oxygen sensors in total. Two of the oxygen sensors are used to monitor the air fuel ratio in the six cylinders (one sensor for each bank of 3 cylinders). The other two oxygen sensors monitor the...

Hello. Your vehicle should be equipped with four different camshaft position sensors, one for each of the engine's camshafts. They are mounted in the front of the cylinder heads, near the camshaft actuators, across from each other. The sensors should...

Hello. Thanks for writing in. The universal oxygen sensors, a bad connection, or a bad catalytic converter can all be the cause of the codes (https://www.yourmechanic.com/services/check-engine-light-is-on-inspection). If you can you access to a known good oxygen sensor and test it...

The bearing is contained within a unitized hub assembly (https://www.yourmechanic.com/services/wheel-hub-assembly-replacement) that is bolted to the knuckle. The entire assembly is replaced (i.e., bearing with hub). A calibrated torque wrench has to be used because the axle retaining nut has to...

Hey there. Starting systems are very simple. If your issue relates to it, it can only be a few things. Let me start with having the starter tested. When you take a starter in to get 'bench" tested, the test...

When you command air conditioning or heat there are mode doors that direct the airflow to the requested place. Positions are floor, windshield, vent /floor, and defrost/floor. The doors move in a housing that has a tight fit. These doors...