Hi i have some problem witj my chevy cruze 2017 Shown p02...


Hi i have some problem witj my chevy cruze 2017 Shown p0234 Mechanic's Assistant: What is the model of your '17 Chevy? Cruze Mechanic's Assistant: Are you fixing your vehicle yourself? What have you tried so far? ...

Hi i have some problem witj my chevy cruze 2017 Shown p0234 Mechanic's Assistant: What is the model of your '17 Chevy? Cruze Mechanic's Assistant: Are you fixing your vehicle yourself? What have you tried so far? Yes mah self Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? Only this issue

Automotive Expert
Hello I'm Rick from just answer, sorry to hear about your cruze issues as I know how frustrating this can be, if you see a phone call request you may choose to ignore that as this is generated through just answer not me personally.... The code p0234 indicatesthat the ECM detected the actual boost pressure that is greater than the desired boost pressure by a calibrated amount...possible conditions for this would be loose clamps cracks or other damage and the air take duct system or a collapsed or restricted intake duct system restricted air filter any air flow restriction any air leak between the turbocharger and the throttle body including the charge air cooler system any splits kinks or improper connections at the vacuum hoses, any vacuum leak restricted leaking or incorrect routing of hoses going to the components like the turbocharger wastegate solenoid valve missing or restricted leaking [exhaust](/topics-exhaust-chevy/) components or an exhaust leak between the turbocharger and the exhaust manifold restricted or leaking turbocharger oil supply line or loose or incorrect insulation of any of these components, it is more than likely a aired intake duct system or a loose connection that is probably causing this issue as it is somewhat common on these

I sir. Sorry I was so busy, I didnt have chans to continue with the troubelshoting. Tomorrow i will continue and will let you know.
Automotive Expert
no worries, ok

What others are asking

Traction control light on, brakes engage
A few different faults can cause this sort of malfunction. The most likely would be the ABS control module, traction control sensor failure, traction control module, or a wiring fault. Any of these issues are causing the car's computer to...
hi do i need to remove the upper intake manifold to change the coil pack on a 2007 montana sv6. one bolt seems to be under the man
The process to remove the coil does not call for the upper intake to be removed. It calls for the upper trim cover only to be removed. You may have to use a small swivel socket with a short extension...
Thrumming and vibration under feet when driving
Hi, thanks for writing in. The noise and vibration you sense could be engine vibration passing direction directly into the body of the car. This normally should not occur, but it can happen when engine mounts or a transmission mount...
Trouble with the traction control
As you may know, the traction control system monitors the steering stability of the vehicle and engages when loss of traction has been detected. This is done by the use of electronic sensors that communicate with the Power Train Control...
Filling up at the gas station.
The issue is the purge vent hose on the fuel filler neck (https://www.yourmechanic.com/services/fuel-filler-neck-replacement) is either leaking or it is plugged up causing the fuel system to vapor lock making the fuel not flow into the fuel tank properly. Check the...
Whine from 2011 f150 drivetrain
Hi there. If the replacement transmission you installed was used, it's quite possible that some component inside is damaged as well. However, it is more likely that the initial diagnosis is incorrect if you are still hearing this pining sound....
My radiator fan is shaking and rattling.
Hello, thank you for writing in. The fans can cause the vehicle to shake and vibrate. If you suspect the problem lies with the fans, start there. Check for any broken fins, extra noises, debris, or other obvious signs of...
Engine misfire, cylinder 1. Car won’t start or turn over. Thoughts?
Hi Dave. Thanks for taking time to contact us today. Generally speaking, if the engine will crank over but will not ignite, and an engine misfire code has been detected, the root issue is likely going to be ignition related...
Cant get timing belt over tensioner
During removal of the old belt, a special tool is used to position the tensioner in the fully retracted position, which makes it easy to slide the new belt over. On removal the instructions are to loosen the belt tensioner...