If the engine shakes on acceleration even in neutral, then there is an imbalance in the rotating assembly of the engine. This could be caused by an engine peripheral such as an alternator or water pump or an issue with...
The smoke could be from leaking oil that is dripping on a hot engine part, such as the exhaust manifold, and then vaporizing. An antifreeze leak is also a possibility. To resolve this, on a mobile basis, right at your...
The tie rod ends for your vehicle, both the inner and the outer ends, are available for separate purchase. If you bought these tie rod ends yourself from an auto parts store, they're "roughly" $50 each or $200 in total...
If your steering wheel has suddenly become hard to turn, and a leak has appeared underneath your vehicle, it is very possible that it your power steering fluid has leaked, and has made your steering wheel hard to turn. Power...
This is a common issue when driveshaft u-joints begin to fail. When there is too much clearance in the U-joints to the drive shaft, this type of clunking sound and slight kick back when stopping will occur. This is a...
If you want to swap the 2002 and 2005 4.0 engine then there should be same basic engine will be the same but you will have different external components that will need to be swapped out to match the car...
Hi - yes, a master cylinder problem, or a leak in the brake system anywhere, could cause "sudden loss of pedal". Check your brake fluid level first for low fluid. If fluid gets low enough that air gets in the...
Hi Nathan. Thanks for contacting us today. The check engine light will illuminate any time the ECU detects a mechanical or electrical issue. This creates a OBD-II trouble code and stores it in the ECU. In most cases, the code...
Hi there. Your steering wheel adjusts so that it can be in the ideal position for you while driving. Adjusting the steering wheel only takes a few seconds: 1. Locate the steering wheel lever, which is to the left of...
Hi there. When the Check Engine Light comes on, it will store a trouble/fault code in the engine control unit. It will remain on as long as the ECU continues to see the fault that turns it on. If it...
Quite often, when one mechanical problem occurs, others are quick to follow. In most cases, they are not related to the same components being faulty. It is possible that during service of replacing or cleaning other parts, a battery cable...
You might be right. The slave cylinder is a hydraulic component. When it leaks either internally or externally, it will cause a symptom such as the one you are describing. In your vehicle the transmission need to be removed to...
Hi there. It is not terribly hard to do a V8 swap on this vehicle. The main thing that is needed is the retrofit kit. This makes the job easy and it will make it to where everything fits well....
This vehicle has many technical bulletins that pertains to wiring issues with pins and connectors to various modules and control units in the vehicle. This issue is one that is hard to track down, since it is an intermittent connection...
Hi there. Unfortunately, the pocket scanner won't help us diagnose this clicking noise for you. In order to correctly diagnose this issue, a professional mobile mechanic would have to complete an OBD-II diagnostic test with a digital scanner that would...
This can be quickly resolved if you request a no start diagnostic. Among the possibilities are malfunctioning throttle and air intake components, such as the idle air control valve, throttle position sensor. mass air flow sensor and so forth. There...
Hello. Exhaust systems can make a variety of sounds that we would not intuitively expect. When I was first learning about exhaust systems I was surprised to find out how dynamic they can be. I am assuming you are speaking...
If you do not hear the relay click, you may be losing power before the relay or the relay itself could be faulty. I would enlist the help of a technician who is proficient in electrical diagnosis, such as one...
Hi. The cluster will most likely need to be replaced as they can not be re-calibrated. To test the cluster, a certified technician would be able to hook up a computer to the car to read out what the various...
Hi Ester. Thanks for contacting us today. The first step in diagnosing a problem like you've described is typically tracing and verifying electrical connections that engage the starter. This would begin with the car battery, followed by ground wire connections...
The code related to the ignition module suggests that either the ignition module itself is bad or the connections to it are not good resulting in erratic ignition timing and potentially misfires. In some cases, depending on how the ignition...
Hello, thank you for writing in. Losing reverse can happen for a wide number of reasons. To simplify things, start with a full inspection. This will include checking the level and condition of the transmission fluid. If it is low...
Hi There, This code relates to your Evaporative Emissions system. Your car has a small purge valve called a purge solenoid that controls the venting of fumes from the fuel tank as these fumes build up inside, particularly when you...
