Popular questions

A muffler falling off of a vehicle is usually the result of the hardware that keeps it fastened to the exhaust system failing or the muffler being rusted out near the flange that is bolted to the rest of the...

Before driving, it’s important to adjust the height of the seat belt so that it is at a safe height. To raise the height of the shoulder strap, slide the belt adjuster upwards to the desired position. To lower the...

The flex pipe broke due to the motor mounts are bad and mounts should be repaired first and then an exhaust shop should be able to just replace the flex pipe for you.

Hey there, thanks for writing in about your 2013 Range Rover. You may have a problem with the throttle control that may be dangerous to drive. There are many other possibilities, such as a vacuum leak, faulty mass air flow...

The trouble codes that you have downloaded have not arisen due to the use, or non-use, of the fuel additive. Code P0841 simply refers to an abnormality in the transmission fluid pressure sensor circuit. Possible causes of that code include...

If all future instances of stalling are on right turns, and none are on left turns, a possibility is a chafing wire harness that only comes into play on right turns. Does the car stall at ANY stops (traffic lights,...

If your head gasket has gone bad, stop driving the vehicle as soon as possible. A head gasket replacement does require removal of multiple engine parts to replace and is usually a costly repair. This is why many people decide...

Hi there. The part number 4593839AB is referred by the Mopar dealer specific manifold actuator part. The part number 68166449AA is referred by the Chrysler dealer specific manifold actuator part. The two parts are the same, but the difference is...

Be sure you have a fully charged battery that passes a load test. Once you have a confirmed good battery, if the starter motor is not functioning that means the starter circuit, or the starter motor itself, is faulty. To...

Hi there. A misfire code is set when the engine computer sees a slow down in one or more pistons due to incomplete combustion. This can either be from a lean or rich condition. The task at hand is to...

There are a number of driver-set functions which may cause the "3-beep" symptom: "top of the hour" clock warning (so you can catch the news), speed warning, icing conditions warning, etc. These are all set on the On-Board Computer. Check...

Hi there: It's always best to get a second opinion on serious repairs services such as replacing a head gasket. In fact, in many cases, the cost or side effects of a blown head gasket can only be determined once...

The pink wire is battery voltage supply to the sensor. If the battery voltage is 12.6 volts (it should be; otherwise you have a battery problem), you should read 12.6 volts on the pink wire, not 11.7 volts. You may...

The clogged line caused the evaporator case to flood out. The problem is the blower motor and the blower motor control resistor may of got flooded out with the water and caused them to short out. If you can get...

Hi there. The code of P2270 is coming up for an issue that is causing the emissions to be out of calibration. Check the following conditions on your engine. Check For an exhaust leak near O2 sensor For a...

High engine idle can result from things like vacuum leaks, a dirty or faulty idle air control valve or potentially an improperly adjusted throttle stop. The idle air control valve reads the air intake as it is mixed with fuel...

Hello there; there are many different faults that can cause your 1996 Mazda 626 to have very low or no air coming from the vents. The most common failures are the blower motor, blower motor resistor, or a wiring harness...

Billing question sent to CS for the cost of replacing a timing belt on a 2013 Chevrolet Cruze LS.

Hi. This might be due to the theft deterrent system being activated. The key for you vehicle has a coded chip that is programmed to your ignition switch. If the switch fails to recognize it, it will think you are...

If the push rod came loose from the clutch pedal, it may be possible that the retaining pin simply slipped out, or the push rod is broken. I would recommend having a professional technician, such as one from YourMechanic, examine...