Popular questions

Hello. Most of the time if all of these stopped working at the same time then you either have a failure in the body control module or in the communication module. Most of the time this is a body control...

When a car rattles on start up, there is a possibility that it is an engine knock. An engine knock will sound like a tapping from the engine block. The more common causes of a rattle on start up are...

It sounds like you may have a clogged catalytic converter. The catalytic converter converts toxic exhaust gases into less harmful pollutants that are suitable to be expelled into the atmosphere. When this is clogged, this causes these gases to be...

We do not normally deal much with aftermarket modifications here, nor do we endorse specific brand or manufacturers of components. I do have to say though, that you are going about this modification in a correct manner. You will want...

You are correct, there is no hex pattern machined into the component. There is a special tool that can be used to remove the inner tie rods. Sometimes you can get a large wrench to work. There are only two...

Hello. I would need to know what size engine that you have in your truck to be able to pinpoint what the issue may be. If it is getting spark then I would usually start by checking the fuel pressure....

If you’ve had a flat, the first step is to get off the road and install the spare tire. However, you also need to make sure to store the flat tire properly in the trunk. Here’s what you should do:...

Although there were recalls on your model year to repair fuel system leaks, due to defects, I see no indication of any known problem, issue, or defect with the fuel filler door itself. The database I used to check for...

You will need to get the axle removal tool at a parts store and hook it to a heavy duty slide hammer. Give it some good raps with the slide hammer with the tool behind the axle joint. This should...

Hey there. If you're using one of those "quick strut" complete assemblies for the front, then you don't need anything special, although an impact gun and/or ratchet is helpful. Rear shocks are just as straight forward. If you would like...

Hello. Though there are a lot of things that can cause this typically it is due to an issue with a failure in a spark plug or an ignition coil failure. If there is not a check engine light on...

Hi there. If the engine continues to burn coolant then you may have a warped block or there are a few other places where coolant can enter the engine. I have seen cracks in the timing cover and in the...

The underlying fault depends on exactly which codes have been stored by your vehicle's OBD-II system. Those codes can be downloaded using a hand-held scanner but then each code has to be separately diagnosed, that is parts have to be...

While keeping your tires properly inflated is very important, it’s also essential that you check their condition regularly. This can help you spot potential problems before they become real issues, and may help prevent a blowout from occurring. Here’s what...

A rough idle can be caused by many things. Something as simple as a bad spark plug wire or bad coil can cause a vehicle to idle rough. Since you have an overheating issue as well while driving, the problem...

If the CV axle shaft is truly bent, as apposed to having just damaged CV joints, such damage will typically only happen in a collision. The axle shafts are very thick strong steel and the impact required to bend a...

This may be an issue related to what is called an idle air control module. This is a module that regulates the amount of air that is allowed into the intake system as it is mixed with the fuel before...

It is possible that you could be having internal transmission issues. These issues could be mechanical (if something is bent or broken), electrical ( a shorted wire or disconnected circuit), or hydraulic (a restriction in fluid flow). I would recommend...

My first thought is, what code is the TCM (transmission control module) setting? Usually when a vehicle won't go faster than 40 mph, the vehicle has set itself into limp mode. It does this to protect itself from what it...

Hi there. Try turning the steering wheel back and forth while trying to turn the key in the ignition. There is a steering wheel lock inside the steering column that could be bent or broken if the ignition switch will...

If you are getting loss of power and have a warning light on your vehicle may be in failure mode and will need to have the systems scanned for failure codes like one of the wheel sensors or transmission transfer...

The brightness of the instrument panel can be adjusted to your liking. To adjust the brightness, locate the instrument panel light control, which is on the bottom right side of the instrument panel. Rotate the control clockwise to brighten the...

Hello. If the shifter is moving fine and the truck responds to the shifter position but does not move when the transmission has more than likely failed. If there is no response at all, then it may be the shift...

Hi, in this case it could be any of these things that you've mentioned. I would start at checking the battery for proper voltage. If voltage is correct then I would check the fuel pump and relay. If there is...

Diagnostic Trouble Code P0352 can arise if the circuit to these components (to the coil) has a fault. It can also arise if there is a vacuum leak at the intake seal to that cylinder (cylinder No. 2 in your...