Q: Car computer showing several fault codes.

asked by on December 29, 2015

My engine computer is giving me several fault codes, including P0352, P0302, P0300, P0305, P01297108.

Spark Plugs Replacement $96.63 - $627.86 Get a Quote

I would have a technician tune the car up and replace the spark plugs and coil packs. That is the code for misfire and coil pack problems. Code p01297 is a code for the map sensor. You could have a shorted wire going to the sensor or the sensor itself could be bad. I would have a technician check voltages on that as well.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing

What others are asking

How much cost to fix ignition switch? 2008 Dodge Sprinter

Hi there - unfortunately, this is not a service YourMechanic can offer at this time. Thanks for thinking of us though!

Truck has trouble starting, idle's too low, losing power, check engine light is on.

You may want to try and run some combustion cleaner into the intake. You can get the good cleaner from any Ford parts store. You use a small rubber hose and allow it to get sucked into the engine slowly...

Car Starts And It Shifts Gears , But Won't Reverse , And In Drive It Barley Goes And When It Does It Jumps And Jolts. Transmisson?

Hello there, the transmission being unable to shift into reverse is a common issue for vehicles as they age and increase in mileage. There are a few common causes for this malfunction. The most likely would be low transmission fluid...

How do I use lane change assist?

Lane change assist makes it easy for you to signal a lane change. Instead of pushing the multifunction lever all the way down, and having to return it to its base position when you’re done changing lanes, the lane change...

Car refuses to drive once dash lights turn on.

I would have a second opinion by a different mechanic to confirm. The Check Engine Light and Coolant Light may be an indication of another problem, and the computer may go into a failure mode and will limit throttle and...

Instrument cluster is off with a P0600 reading

Hello there, the P0600 code is not one that is normally seen on your 2003 Mercedes ML350. The P0600 code tells us there is a communication link issue with the ECU. This may have been caused by the fuel pump...

i need to find out how much to replace a subframe on my vehicle

Hi there. Unfortunately, our mobile mechanics only complete basic repairs and service on most cars, trucks and SUV's in the United States. A sub frame replacement is something best completed by a body shop or professional repair facility. Thanks for...

Oil leak behind oil filter

There should be an oil pressure sensor located near the filter housing. Check to see if there is a leak at the sensor. At idle, there should be about 15PSI of pressure and about 50-60PSI at around 3,000 RPM's. There...

Hesitation when accelerating from stop.

Hi, there is a list of possible problems that could cause the hesitation from a stop on this engine. The intake system is known to have vacuum leaks and also coolant leaking into the intake. The mass air flow sensor...

Related articles

P0332 OBD-II Trouble Code: Knock Sensor 2 Circuit Low Input (Bank 2)
Trouble code P0332 means the PCM is receiving a reading that the knock sensor is too low, which can result in higher emissions and engine problems.
P0083 OBD-II Trouble Code: HO2S Heater Control Circuit High (Bank 1 Sensor 2)
P0083 P0083 code definition P0083 is a general OBD2 code indicating a issue with bank 2 intake valve control solenoid. This code may be seen with P0081 and P0082. The vehicle also has a bank 1 valve control solenoid. What...
P2649 OBD-II Trouble Code: ‘A’ Rocker Arm Actuator Control Circuit High Bank 1
P2649 P2649 code definition ‘A’ Rocker Arm Actuator Control Circuit High Bank 1 What the P2649 code mean P2649 is an OBD-II code for the engine control module (ECM) detecting the ‘A’ rocker arm actuator control circuit for bank 1...