Q: 2013 Dodge Charger Thermostat P0128

asked by on November 23, 2017

I have a 2013 Dodge Charger w/MIL showing code P0128, P0128, P0128. I put in a new thermostat but the MIL is still on? Why?

My car has 87000 miles.
My car has an automatic transmission.

You will need to have the engine scanned and compare when engine is cold the engine coolant sensor and the ambient air temperature sensor to see if they read within 5 % of each other and the engine started and the engine coolant warms up with in 8 minutes to 180 degrees. If the inlet ambient air temperature is not accurate then replace sensor.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing

Experienced Mechanic?

Earn up to $70/hr

What others are asking

09 GMC Acadia slt2 low oil pressure light shut off [engine](/topics-engine-gmc/) display came off and I checked the oil and it was fine started it back up and the low oil pressure display went away.is it okay to drive

I have been having with my Jeep not starting. A friend tried to jump start it but nothing would happen. The dome light worked however the horn did not. Tried a different vehicle and jumper cables and the Jeep cranked. Ran fine the rest of the day and the next day. This morning my Jeep started fine. I drove to the gas station, came back out and it would not start. Had the same issues trying to jump start it. Napa Auto Parts walked over and tested the battery which read 12.6 volts, the Napa guy was able to start my Jeep with a jumper box. He said the alternator was good too. When leaving to drive my Jeep home, several lights in the dash were flashing, the radio would not work and the speedometer would not work. Got home and let the my Jeep run idle for 20 minutes, then it just died. The Jeep set for several hours while I was at work. I got home and tested the battery with a multimeter and it read 12.6 volts. Tried starting it and it would not do anything. Four hours later, I wanted to go outside to see if my headlights were working turned them on and they were. I thought let me try and start it. The Jeep started right up with no issue. Could this be a bad battery even though it is showing 12.6 volts, the Napa guy did say the CCA were low but the battery was good. Would a faulty crankshaft cause issue that would mimic a bad battery, alternator or starter? I'm at a loss and don't want to waste money buying a battery if it is something else.

I have a 2002 Dodge ram 1500 sport and tried to install aftermarket radio and it did not work I put the old one back in and it's n

Check fuse number 2 and 51 and 18, 22 and 28 to see if all are good. If still not working then seek professional mechanic like one from YourMechanic to do further diagnosis.

What does it mean for a nissian maxima 2007 for a service engine soon

Claimed by Jeff Engstrom

Transmission line pressure too high for too long 2006 dodge magnum

It sounds like you downloaded Code P1745 which refers to line pressure being out of range (high) for too long. The line pressure solenoid could be faulty and/or the solenoid harness is open, shorted, or has high resistance (poor electrical...

My truck isn't idling right and is burging a lot of gas

Code 12 will always flash when checking for codes. With the engine off, there is no ignition pulse so Code 12 is normal to see. Code 34 has to do with the MAP sensor. Manifold Absolute Pressure. It's basically a...

Brake light circuit warning light illuminated - 1998 BMW 323is

Sometimes, there is just enough corrosion on the end of the bulb to trigger this warning despite the bulbs illuminating correctly. Using some emory cloth or very fine sandpaper, rub the contact end of each of the brake bulbs to...

Soft breaks

When you say (and now my brakes are still soft) this means you had soft brakes before and after the master cylinder was replaced. If you have soft brakes, it is caused by air in the brakes, problems with flexible...

Can't start car due to security system

Hi there. Your vehicle's anti-theft system seems to be malfunctioning. A change of ignition cylinder will cause this problem because your vehicle thinks someone attempted to steal it. It is possible to bypass this anti-theft system in order to ensure...

Related articles

P2147 OBD-II Trouble Code: Malfunction with the Fuel Injector Group A Supply Voltage Circuit Low
P2147 P2147 code definition P2147 is a generic OBD-II diagnostic trouble code indicating a malfunction with the fuel injector group A supply voltage circuit low. What the P2147 code means The P2147 code means than the fuel injector group...
P0239 OBD-II Trouble Code: Turbocharger Boost Sensor B Circuit Malfunction
P0239 P0239 code definition Turbocharger Boost Sensor B Circuit Malfunction What the P0239 code means P0239 is an OBD-II generic code triggered when the Engine Control Module (ECM) detects an intake boost pressure sensor B input malfunction when compared to...
P0420 OBD-II Trouble Code: Catalyst System Efficiency Below Threshold (Bank 1)
P0420 code means that either the upstream or downstream oxygen sensor in the catalytic converter is not working. Replacing these parts can fix P0420.