Hello. Most of the time, when this code comes up, it is either caused by a leak in the EVAP system or a failure of the sensor. Typically, the issue is the sensor itself not reading correctly. I will usually...
Hello. If the ignition lock cylinder housing that is mounted on the steering column itself is broken, then yes - you will have to purchase a new steering column, as that component is fabricated on the steering column and is...
Oxygen sensors don't work in that voltage range. Oxygen sensors range from .1 to .9 volts. When the vehicle is running normal the sensor ranges between .4 to .6 volts. The O2 voltage should change constantly going above and below...
When it comes to a four wheel drive vehicle, it doesn't really matter what gears you use, as long as they match on the front and rear. So, if you wanted to switch to a 355 gear, that would be...
The lights and other accessories are controlled by the body control module. If the module does not turn off the power to these systems, then it may be the problem. You will need to have the system tested using the...
Hello. If you are not getting any pressure to the pedal then it may be possible that there is an issue with the clutch master cylinder. The clutch master cylinder is the component responsible for generating pressure for the clutch...
Hi. Your shift lock switch may be engaged. It will be in one of two places. On the top of the steering column of the instrument cluster or right by the shifter itself above the Park icon on the shift...
If your car is equipped with Heated Seats, you have an additional way to provide comfort during cold weather. Heated Seats can also help with muscle aches and cramps from long driving sessions. Here’s how to work your system: ...
Hi there. Sounds like the variable valve timing sensor (VVT) is not functioning correctly. Check the wiring harness to the VVT and make sure that its connected. If the harness is good, then remove the harness and remove the VVT...
Hello, thank you for writing in. When the engine is locked up, it means that it is stuck in place for one reason or another, and it will not rotate like it normally does. This is directly related to the...
Hello. If the oil was completely empty, then you may have a serious engine failure. I would first add oil to it and then try starting it. If it still does not start and makes a lot of noise when...
I would recommend having your vehicle inspected by a qualified professional to determine which check engine light codes are stored in your vehicle system. Once this has been done the mechanic and have a better indication of what the vehicles...
Hi there. You might want to watch this video on replacing the EGR valve on a Dodge Avenger to determine where it is located and whether or not you feel comfortable completing this service. It is rather easy when you...
Hi Michele. Thanks for contacting us tonight. There are a few possible reasons that your headlight is not working after replacing the bulb. In most cases, it's because the electrical harness is either loose or damaged. It could also be...
It is possible to remove the head while the engine is in the car, but it's going to be tight. This can be a difficult and even dangerous job. Unless you feel very comfortable with this type of work, you...
Noises like these generally come from worn suspension components or ones that may just require some lubrication. Ball joints and control arm bushings are usual causes for this type of noise. Hire an automotive technician experienced in vehicle steering and...
The two motors are from two different years and one is a car and other a truck motor. The two motors have different specifications for compression and camshafts internally. You will also have different external problems with sensors, fuel injection...
Try holding down the "HOLD" button for about 5 seconds and this should correct the problem. If it does not, you may have a computer issue that will require diagnosing with a scanning tool. In this case I would recommend...
Hi there. Assuming the growling noise in your steering wheel is inside the vehicle, this would lead me to believe there is a problem with steering shaft bearings. It is rare for these bearings to fail. It could also be...
There should be no need for you to have to replace your transmission yet. You should get a full diagnostic check from YourMechanic first before any part or component replacement. The problem you describe can be caused by a few...
Hello, and thank you for writing in. The Ford electronic throttle bodies have a history of failing unfortunately. You may even want to look up warranty and recall information for your vehicle based on your VIN. The new unit that...
Hi there, thanks for writing in. This P0446 trouble code relates to the evaporation control system circuit, which is a restricted vent path for the EVAP (Emergency Vehicle Accident Prevention) system. There is a solenoid in this circuit that sometimes...
The code P0132 is for the O2 sensor in the rear manifold of the engine. The code is for a short to power and should be checked to see if the harness is shorted. You should not have the sensor...
Hello - it is possible that the pinched radiator hose (wrong hose?) is interfering with the engine drawing additional coolant between hot/cold cycles. If it were me, I would drain the coolant - you need to do that to put...
Hi there. By looking at the photos that you have provided is shows that the PCV (positive crankcase ventilation) valve is blowing by and causing engine oil to go through the PCV tube. Since your engine has a turbo on...
