Popular questions

This should not have anything to do with the oil changed that was performed, however occasionally, parts get left unbolted or become loose and can drag on ther ground causing a scraping or rattling noise. This can also happen sometimes...

The heater control valve may not be opening fully and/or the heater core, beneath and within the dash, may be partially plugged. In both cases, the result would be inadequate heated engine coolant flow through the heater core and no...

When an intake manifold gasket fails, it can leak coolant into the engine and contaminate the engine oil, so in some cases it will be necessary to change the oil in conjunction with this service. Vehicles with plastic intake manifolds...

No, signal on the instrument cluster concerning the engine temperature usually points to no signal coming from the coolant temperature sensor. This can be caused by a broken wire along the circuit, loose connection, or failed temperature sensor. If the...

Hello, thank you for writing in. If you have two issues with the power steering fluid at once, it would be very unfortunate. The lack of power steering fluid is cause for concern alone. If you are low or out,...

Hello, thank you for writing in. There are parts of the charging system, like the alternator output, that are monitored directly by the computer with sensors. However, there are enough sensors in the system, the aspects that are not directly...

This may be related to a dirty or failing idle air control valve. The idle air control valve monitors the air intake as it is mixed with fuel prior to being injected into the engine at low speeds and at...

The computer in this car controls if the starter turns or not. You will need to have the computer scanned to see if the alarm is active. Have the batteries changed in the remote key FOB to see if this...

Hi there: Without being there to physically inspect your Mazda, it's impossible for us to tell you what is causing your fuel leak. If it's with the fuel rail however, you should take the time to replace the entire rail,...

Hello, thank you for writing in. Resetting the system should be as easy as holding a few buttons and accessing the right menu. From there it should be rather straight forward once you reach the menu. On some models, you...

Grinding, squealing, or other "noise" on braking is usually related to a brake pad/rotor contact problem. These surfaces "mate" when you apply the brakes and if there is scoring on the rotor, rust, dirt, irregular wear on pad or rotor,...

Although the blower motor might not be running because a fuse blew, the problem is fuses usually blow due to an electrical malfunction in the circuit such as a short. Fuses are simply "protection devices" and when they blow it...

Hello - there a number of possibilities for a "no start" condition: dead or weak battery, ignition switch, starter solenoid or motor. I would recommend a starting system inspection by a mobile, professional mechanic, such as one from YourMechanic, who...

Hi there. If the starter was replaced, first check the battery cables to the starter and make sure that they are tight. If the cables are tight, then the issue could be that the clutch may have broke causing the...

Sorry to hear about your battery being stolen. One of our mobile mechanics can come to your location and replace your battery cables and install a new battery if you'd like. In order to provide you with a quote, we'll...

Billing question sent to CS for the cost of repairing a plugged up fuel system on a 2014 Porsche Panamera.

If the engine is to the point of making knocking sounds, there is probably internal damage at this point due to the low oil level. If the crankshaft is scored from lack of oil, then oil pressure will not return...

Hello. It is very possible that the timing belt broke or the engine seized. I would usually check the oil level first. If it is empty then there is a serious issue. If there is oil then I would try...

Hello. The best resource that would give you great and factual reviews for 7 seat SUV's would be Edmunds.com. Check out what they have to say about all makes and models, and you should be able to find the best...

As you know, code P2076 indicates that the signal for the tuning valve position sensor was not within a specified range. When this happens, often times it is related to a power or voltage supply issue, an open circuit or...

Hi there - while not an epidemic problem, rear ends that are "worked" harder (i.e. trailer towing, off-road, etc.) or simply high mileage such as yours will see this problem. There is enough of a side load on these clips...

Hi there. Although the creaking noise might be caused by a tie rod wearing out, it's also possible that another steering system or suspension component is faulty and causing the noise. You might want to have one of our mobile...

This misfiring may occur when spark plug wires are exposed to oil and short out the ignition wire. This is caused a leaking valve cover and a broken seal around the spark plug holes. You will need to have your...