Popular questions

You need to have the engine idle relearned by disconnecting the battery for two minutes and then starting and idle engine in park and then drive for two minutes each and then do same with a/c on and blower on...

Hopefully, the two stalling scenarios have only one cause. Among the possibilities are a faulty torque converter lock up. You might be able to detect that with a sophisticated scan tool, such as the Tech 2. If the level of...

Hi there. Thanks for writing back. Here is some information about the P1005 Dodge trouble code. It's actually specific to Dodge & Chrysler vehicles, so it's hard to find information on the code. P1005 code indicates a Manifold Tunning Valve...

Hi there. When it comes to engine oil additives, I ALWAYS follow the recommendations of the manufacturer. In this case, Rislone would be correct. Zinc additives or ZDDP is essentially tiny particles of metal that infuse onto engine parts, specifically...

There is a technical service bulletin (TSB) GM has put out concerning a bad ground to the electronic brake controller module or EBCM. This causes a loss of communication and sets the ABS light. There are fault codes associated with...

If your vehicle is equipped with a navigation system, it will help you find directions where you need to go. Your navigation will appear on the center display. To use the navigation system. Type in the address you need...

If the cooling system gets low at all, usually the first thing you notice is that the heat goes away. The system could seem to be full, but have air pockets causing your problem. That can be solved by bleeding...

Hi, thanks for writing in. This is most likely related to a faulty coolant fan switch. This is a relay switch that comes on when the temperature of the coolant system reaches a certain level. When this switch is faulty,...

The fuel shut off valve is a solenoid that is controlled primarily by the shut off relay. The message you are receiving is telling you the circuit has low voltage. This means the solenoid is not energizing the way it...

Hello there, many different faults can cause the MAF sensor on your 1999 C180 to cause the car to run poorly. If the MAF sensor was replaced and the problem still remains than the most likely faults are a vacuum...

Hi there. I understand how frustrating things like this can be. Base on what you've described, the year, and mileage of the vehicle it sounds like your battery has gone weak or failed internally. A good battery test with a...

Hi there. This is typically caused by warped rotors. When the rotors are warped, the steering wheel will shake when applying the brakes. This is a common issue. I usually measure the rotors to see if they are good, but...

The 5 digit code should be printed on a white label in the trunk. Open your trunk and look on both sides of the hinges where the trunk lid opens. On one side of the hinge is a white label...

I am going to assume you have a 2.2 liter engine with the air conditioning option on your vehicle, since you mentioned multiple fans. Both fans should turn on while the vehicle is running and the A/C is switched on....

The inertia switch is supposed to totally disable the fuel pump power supply when the vehicle is in an accident or rolls over. You will need to check the power connector into and out of the inertia switch to make...

Hey there. The problem sounds like the front brake pads have worn down to metal and now the brake pad has worn to the point it came out of the caliper bracket causing the pedal to drop. You should not...

Although some service manuals do refer to engine removal, that advice is in error. So long as the engine is properly and safely supported, the lower control arms can be readily removed. The bushings on these arms are not separately...

Hello, It sounds like the rack and pinion may have been damaged during the process of replacing the tie rods. If you are leaking power steering fluid, I would recommend having the rack and pinion checked. It is also very...

Hi Lidia. Thanks for taking time to contact us today. While it's not unusual for new brake pads to rub a bit or for excessive brake dust to create squeaking noises after replacement, the type of sounds you are describing...

Hello. If the noise only occurs when turning, it is typically caused by a failing CV axle. When one of the joints on the axle fails, it will start to make the noise you are hearing. I typically get the...

Hello, thank you for writing in. The vehicle may be having one of several issues. First, if you replaced the fuel filter (as should always be done when the fuel pump is changed), you need to make sure it is...

Based on your question I believe that you are having an issue with the serpentine belt tensioner on your truck. The serpentine belt is on the front of the engine and drives all the accessories attached to the engine. This...

Vibration may be caused by many different things such as faulty spark plugs, poor fuel pressure or misfires. Other things such as a faulty idle air control valve may cause the engine idle to drop below the normal idling RPM...

If you want to remove a CD from your vehicle’s CD player, simply press the eject button, which sits next to the CD slot. The CD will be partially ejected from the slot, and you can remove it all the...

Hello. Since the Check Engine Light is on, I start by scanning the computer for codes. This will give me a place to start. Most of the time, this is caused by a failing speed sensor on the transmission. When...