Q: How do I set the park all doors unlock mode?

asked by on January 07, 2016

How do I set the park all doors unlock mode?

When your vehicle is set to park all doors unlock mode, then all of the car’s doors will be automatically unlocked when you place the shift lever in P and depress the brake pedal. To set the park all doors unlock mode, follow these steps: 1. Engage the parking brake. 2. Place the shift lever in P. 3. Close the driver’s door if it is not already closed. 4. Turn the ignition to On. 5. Press the unlock button on the master door lock switch (located on the driver’s door), and hold. After about five seconds you will hear two clicks, but continue holding the button. After about five more seconds, you will hear a single click, at which point you can release the button. 6. Turn the ignition to ACC. This step will need to be done within 20 seconds of step 5.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing

What others are asking

When should a supplemental restraint system component be repaired or replaced?

Most components in your supplemental restraint system (SRS) are designed to be used just once. This applies to all of your air bags, as well as for the seat belt pretensioners in your driver and passenger front seat belts. Once...

Code p0301 replaces all 4 plugs, cylinder 1 and head gasket

Diagnostic Trouble Code P0301 means that Cylinder No. 1 is misfiring but the causes of that misfiring can be very varied. The fuel injector could simply be dead or there is little cylinder compression due to a burned valve or...

Warning lights and PO344 Camshaft Position Sensor

This vehicle came with three different engines and they all have different directions to replace the sensors. The sensors also may have specialized removal and installation procedures that require special tools for the seals and sensors. The code P0344 is...

Lock is not working in the car remote key but unlock is working

Hi. The first thing to check is to see if the interior lights go out after you close the doors. If the system sees a door is open then it will not lock the doors for you. Check fuse #16...

Car shakes when accelerating and has a hard time starting

Shaking or vibration may be caused by many different things such as faulty spark plugs, poor fuel pressure or misfires. Other things such as a faulty idle air control valve may cause the engine idle to drop below the normal...

What does the Side Air Bag Off warning light mean?

The Side Air Bag Off warning light is located on the instrument panel. When the light illuminates, the passenger side air bag is temporarily deactivated. The passenger side air bag turns off when the front passenger seat is not occupied,...

overheating and engine is shaking.

The condition that is causing the electric fans to come on selectively would be caused by the coolant sensor / switch. The sensor / switch is loosing contact connections causing the connections to the fans to cut off making the...

My 2008 Honda accord keeps misfiring on cylinder 2 and i don’t know what to do.

If the plugs are new that is unlikely to be the cause of misfiring. Compression in the No. 2 cylinder should be tested because if you have low compression or a sticking valve in that cylinder, that could cause a...

How do I adjust the terrain management?

The terrain management allows you to choose the best driving mode for your vehicle: Normal, Mud/Ruts, Sand, and Grass/Gravel/Snow. To set the mode, rotate the Terrain Management knob to the desired setting. Be sure to rotate the knob back to...

Related articles

Symptoms of a Bad or Failing Door Latch
If a car door will not stay closed, must be slammed hard to close, or gets stuck and will not open, you may need to replace the door latch.
Symptoms of a Bad or Failing Door Lock Relay
If the power door locks function intermittently or do not work at all, you may need to replace the door lock relay.
Symptoms of a Bad or Failing Hatch Lock Cylinder
Common signs include the hatch lock cylinder just spinning or not turning at all when you insert the key, and the key not even being able to go in.