Q: Clutch not working

asked by on February 05, 2016

My clutch is not working.

Clutch is not working Inspection $94.99 - $114.99 Get a Quote

If your clutch is not working then it may have a bad clutch cable or the clutch itself is bad. A mechanic would typically inspect the condition of the cable and make sure it is moving properly. If it is then the clutch would need to be replaced. I would have a certified mechanic inspect your clutch issue to see what repairs are necessary.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing


Experienced Mechanic?

Earn up to $70/hr

What others are asking

Lights flickering while driving.

Your Dodge Durango is equipped with a computer known as the CTM (central timer module). The CTM is responsible for performing various tasks on your vehicle, one of which is the task of monitoring your Durango’s battery for drainage by...

engine will not start now, after repairs first to the transmission, then alternator and new battery and last, a new fuel pump

If all the other problems started to happen after the transmission was removed and rebuilt, I would suspect that a wire harness has not been connected good or got pinned between the engine and transmission. I would also look for...

The car idles very nicely. When I press the gas pedal it does not pick up speed, rather it sounds like it is dying for air.

From what you describe it would appear that your vehicle is experiencing some sort of engine performance issue. Hesitation when put into gear can be caused by a wide variety of things. Possible causes can range from issues with the...

I am leaking all of my coolant near the rear passenger side tire. What could be the exact cause and how much to fix?

Hey there. This vehicle has a dual A/C and heat system. This means you has a complete A/C heat system mounted in the rear of the vehicle inside the passenger side. The rear system has A/C lines and heater hoses...

Engine swap? Have both VIN numbers don't want to buy if not compatible 2000 saturn LS2

Hi there - since the engine type is "R" for both VINs (position 8 in the VIN), yes, these engines should be compatible. I would recommend using the engine management (computer) and engine wiring harness from the donor vehicle, just...

Vauxhall Corsa D 2013 - Brake Light Switch needs locating.

Hi there. Go to the brake pedal and look at the top of the leg of the pedal and you will see a switch that is mounted on the bracket that the pedal is hanging off of. That switch is...

My Pontiac G6 is hard shifting and engine light is on I got a resd out and it said cam crank sensor do U think that would cause it

It is very possible that a cam or crank sensor could cause the shifting perormance of the transmission to decrease. It is certainly possible to have a check engine light illuminated due to this issue. I would recommend a check...

Engine Malfunction, power reduced

Hello, and thank you for writing in. You are thinking in the right direction. Start by inspecting the throttle body, air intake, and the throttle and intake sensors. Make sure the electrical connections are all clean, dry, and tight. You...

It gives me the code p2649

Hello, thank you for writing in. The vehicle has rocker arms that control the valves where the fuel and air enter the engine, and the valves that channel the exhaust gasses out of the engine. With these rocker arms are...

Related articles

Symptoms of a Bad or Failing Clutch Slave Cylinder
If your manual car has abnormal pedal feel, low or contaminated brake fluid, or any visible leaks, you may need to replace the clutch slave cylinder.
Top Automotive News & Stories – September 3-9
This week's top auto news: Ford's 3D printed future, Dieselgate guilty plea, Toyota Supra prototype spied, LaFerrari Aperta on the road, and more.
How to Troubleshoot a Clutch Pedal Sticking to the Floor
Clutch pedals in manual cars stay on the floor if there's a failed clutch release bearing, slave cylinder, clutch master cylinder, or clutch linkage.