I just replaced the battery, starter, and alternator, but...


I just replaced the battery, starter, and alternator, but my 05 malibu wont start Mechanic's Assistant: Have you checked the battery, particularly the terminal connections? Are they corroded? No, but my key had broken in ...

I just replaced the battery, starter, and alternator, but my 05 malibu wont start Mechanic's Assistant: Have you checked the battery, particularly the terminal connections? Are they corroded? No, but my key had broken in the ignition Mechanic's Assistant: Are you fixing your Malibu yourself? What have you tried so far? I've tried jumping it test the alternator, and the anti theft lift light stays on no blink


Am I speaking with a mechanic
Automotive Expert
Hello and thank you for using JustAnswer. My name is \*\*\*\*\* \*\*\*\*\* I will do my best to assist you. During this conversation you will be given an automated offer for a phone call. You may accept or decline that offer.I don’t personally offer this service so if you take this another tech may call I’m sorry that you’re having trouble with your vehicle. I will do my best to help you resolve them. Please understand that I do not know your knowledge or capabilities so I may need to ask questions to find out basic information to help solve your specific problem. My aim is to give you the best service possible and to help you. If you have any questions or concerns, please don’t hesitate to let me know. Sometimes it may take a moment for me to respond because I may have to look up information about your concern. I appreciate your patience and will provide responses as soon as possible. Have you tried the GM relearn procedure yet?

No how do I dothat
Automotive Expert
HI 30 minute GM relearn procedure: 1-Turn ON the ignition, with the [engine](/topics-engine-chevy/) OFF. 2-Attempt to start the engine, then release the key to ON (vehicle will not start). 3-Observe the SECURITY telltale(this is the security light), after approximately 10 minutes the telltale will turn OFF. 4-Turn OFF the ignition, and wait 5 seconds . 5-Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes (the vehicle is now ready to relearn the Passlock(TM) Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK). IMPORTANT: The vehicle learns the Passlock(TM) Sensor Data Code and/or password \*\*\*\*\* the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6-Start the engine (the vehicle has now learned the Passlock(TM) Sensor Data Code and/or password). Thanks for using Just Answer and letting me help you. I hope I provided what you needed. If you find more help is still needed, let me know by listing out any remaining questions you have on this concern. I hope the remainder of your day is well.

What others are asking

Getting random misfire code.
Your Chrysler sets a P0300 random or multiple misfire code when more than a 1.8% misfire rate is measured during two trips. Countless issues can set this code, from a vacuum leak to a bad coil pack. Your engine is...
Control arm bushings going bad
Bad control arm bushings will cause the issues you have described except for the grinding noise. The grinding noise is most likely the brake pads grinding the rotor surface. Look at the rotors and see if there are deep grooves...
Car won't start
Hi, thanks for writing in. The first thing to do is to check all the fuses (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-fuse) that deal with the battery and the ignition system. There is a possibility while changing the terminals one or more of the fuses...
My car starts up and runs about 15 minutes & dies, after15 minutes it will start right back up, i noticed the fan not turning on 2
Hello there. Unfortunately, there are many faults that could cause your 2004 Chevrolet Aveo to stall and die after 15 minutes. Common faults are the battery, alternator, fuel pump, fuel filter, battery cable, coil, or a wiring harness fault. The...
I'm having problems with code po740
Hi there. In order to be able to give you more exact information I would need to know whether or not the vehicle is equipped with the CVT transmission. It sounds like you have the regular transmission in your vehicle....
We changed the temperature sensor because we broke it and now the check gauges light won't quit flashing, and the temperature gauge jumps to high
Assuming that your vehicle is not actually overheating, this leads me to believe that the replacement temperature sensor (https://www.yourmechanic.com/services/coolant-temperature-switch-sensor-replacement) is faulty or incorrectly installed. It could also be a poor electrical connection at the temperature sensor. An open circuit would...
Cranks but won't start.
Hi there. It seems that the transmission position sensor / switch has a contact issue within it. Remove the harness from the transmission switch and see if there is any moisture on the plug. If there is moisture, then you...
Stripped catalytic converter exhaust flange stud
Yes, absolutely. If the external threads of the stud are damaged, the stud would be extracted, the internal female threads renewed (or a helicoil installed) and a new stud would be placed. If the stud has come out but the...
Car heater was blowing cold air until at highway speeds, then stopped putting out any heat. Dealer says blown head gasket
You may have a clogged heater core which may be preventing the heater from working properly. Generally, a blown head gasket would cause the car to overheat and would eventually get worse to a point where the vehicle would no...