Popular questions

The clues to what that was all about are within the trouble code(s) that were stored when the check engine light illuminated. Those codes, which can be downloaded, are not themselves a diagnostic or pinpoint identification of the failed or...

You stated that you replaced a blown fuse. This fuse can be the circuit that is having a short circuit. You should have a mechanic come and scan the computer to see if there is codes in memory. The problem...

The manufacturer has issued a technical bulletin on this condition. They say that this is caused by residual fluid left in the clutch packs inside the transmission after it was shut off and can cause a slight jerk on cold...

Hi there. A pull to the left can be caused by a few different things: tires and bent/broken suspension components, brake calipers sticking, and/or wheel bearings. I would have to have to know a few things like was the bearing...

This may suggest failing transmission synchros. As you may know, when a clutch drags, it is not letting go of the disk fully which overloads the synchros and burns up the friction surfaces quickly. Synchros work by speeding up or...

The cost varies significantly from the 2WD version to the 4WD version. In any event, the possibility of an on car repair should be considered first. Also, depending on the condition of the transmission, it might be less expensive to...

To play a CD, you will first need to insert the CD. Insert the CD by slowly sticking it into the CD slot, face up. Do not force the CD in; it will feed itself in. When you insert a...

First check to see if any OBD-II codes have set. A real time scanner can be used to check the operation of the throttle position sensor - TPS. TPS faults are a common cause of the symptoms you are describing....

Hello, There are many reasons that may cause a vehicle not to start, however a malfunctioning neutral safety switch can certainly be one of the causes for this. The neutral safety switch will prevent the vehicle from starting when it...

Hello. It sounds like the spark plug wires, distributor cap, and rotor button should be replaced. It may even be necessary to replace the distributor shaft as well. The throttle body should be cleaned as well as having a fuel...

Hi Victoria. Thanks for contacting us tonight. It really depends on the angle in which your tire hit the curb and the original condition of the tire. If the tire is older and has some cracking on the tire, then...

The V6-3.0L Turbo is diesel powered. If that is the vehicle that you have, the oil capacity is 6.8 quarts assuming you install a new filter and, of course, you should use a new filter. In all events, check the...

A thumping is most likely coming from the front rotors being warped, and the pads jumping back and forth in the caliper while braking. The rotors and pads should be inspected and replaced as a set; putting new pads with...

If the Check Engine Light is on, that means that your vehicle's Powertrain Computer Module has detected an important malfunction. During a check engine light diagnostic a certified professional from YourMechanic could download the Codes identifying the malfunctions and diagnose...

If your sitting still without starting, can you shift it out of drive?

Hello - this problem requires a full-function, BMW specific problem scanner and reset tool. This is usually only available at a BMW dealer. I would expect to be charged for an inspection fee as well as the code reset function....

Hello. On your vehicle there is no limp mode trigger that is used for diagnostics. On some newer vehicles this is something that is part of the diagnostic process but not on a 2002. The only way to fully read...

Check carefully under the hood to be sure there are no air large air leaks in the intake system, such as the big boot at the throttle body or any other large vacuum hoses. Sometimes these rubber parts fail and...

Hi there. The engine will not start to break down or lose power at that point. The factory engine does not make that much power on its own so I have to assume you are talking about aftermarket power modifications....

You will need to set the crankshaft to No. 1 top dead center or TDC. There should be marks on the crank pulley that indicates where this is. If you have already done this, you may be 180 degrees out....

Claimed by Kevin Gainer

The shift cable may have come off of the shift selector, or the cable has broken. This would not let the key out of the ignition, since you have to be in Park, and you cannot start unless you are...

Hi there. I see you've replaced the recommended parts that supplement the error code. Another reason why your vehicle maybe not be receiving sufficient fuel is because of a clogged or obstructed fuel filter and pump. When your vehicle gets...

Hello there, thank you for asking about your 2004 Suzuki Forenza. You have a few different faults going on with your car. If you have a 1+2 shift malfunction there are a few potential causes. The most common cause is...

Hello. Thanks for writing in to YourMechanic.com. Unfortunately, this model of Ford bus is not among those we service. In most cases, when a transmission is damaged, or electrical harnesses are faulty, it will trigger and error code which as...