Popular questions

Hi there. The OBD-II trouble code you listed, P0346 is an indication of an issue with the crankshaft position sensor. When this component fails, it will cause the ignition timing system to operate incorrectly, and can be the source of...

Hello - these 2 components mount on each cylinder head, and are partially visible at the "nose" (accessory belt end) of the engine. They use engine oil pressure to vary cam timing relative to the static cam/crankshaft timing relationship. Here...

Hi there. In general, you'll need a full metric socket and end wrench set, a few line wrenches for removing fuel lines and wire pliers for removing fuel lines that are secured via wire ties and of course replacement gaskets....

Depending on the year of the vehicle will depend on how much equipment that will need to be adapted to your vehicle. It is possible to take an OBD 1 or OBD 2 system engine and install it into your...

I would have to say yes! Cars are required to be equipped with a parking brake. The parking brake assists the transmission in keeping the vehicle stationary. When you put your vehicle in “park,” a metal rod about the size...

Hi Christopher. Thanks for contacting us tonight. The P-O705 OBD-II trouble code indicates that the Engine Control Module (ECM) or Transmission Control Module (TCM) has received an input error from the Transmission Range Sensor (TRS). This switch is also known...

Spark and fuel are required for the engine to start and run properly. If the engine cranks easily, odds are it's not a battery or starter issue. Lack of spark and fuel can be caused by a number of components....

Your recommended oil is 5w20 or 0w20 in winter. Your recommended oil type is Delco dexos 1 synthetic blend. I would recommend going to a full synthetic oil using the recommended weight oils 5w20 or 0w20. The full synthetic oil...

Hi there. In most cases, when the engine will idle higher after shifting into neutral or park is an indication of a vacuum leak. It could also be due to a malfunction of the idle control valve, or a malfunction...

Hello. Typically when this occurs it is because there is an issue with the MCU in the fuse box under the dash. This is a module that is used to provide power to the master switch. It can also be...

Hi there. Your issue is the ECT sensor B is not closing the loop when engaged. There is power to the sensor A from the computer, but the sensor B is not connecting when the vehicle is running hot or...

The brake system has rubber seals in it which are not compatible with mineral based oils of any kind. Introduction of these oils in to the master cylinder will cause the brake system seals to swell thus preventing normal operation...

This could be any number of things ranging from a faulty starter relay to potentially a problem with the charging system such as a faulty alternator. If the starting is intermittent and does not require the car to be jumped...

Cleaning your distributor cap is not usually successful. The cap can have problems that cannot be seen with the naked eye. It should be replaced along with rotor, spark plugs, and spark plug wires. The description of your symptoms certainly...

A squeaking belt can be quite annoying when the engine is running. If it is squeaking all of the time this can occur for a number of reasons. I would start with a visual inspection of the belt. I would...

The code P0193 pinpoint test should be done to verify the pressures and sensor indicate the same. You most likely have a defective sensor for the fuel pressure on the fuel rail. Replace the sensor and clear the codes. If...

The most likely cause of this issue is a faulty ignition switch or lock cylinder. One of the tumblers may have fallen out of place causing a connection to the starter when there should not be. My best recommendation would...

The best thing to do is check the check engine light with a scanner and see what code could be stored. This will give you a starting place for diagnostics with your vehicle since three different lights are on. If...

Hello. Thanks for writing in. The diagnostic code that is triggering your warning light it's a fairly generic code relating to a bad reading at one of the sensors. This bad reading can mean that there's an electrical or mechanical...

This may be a sign of warped brake rotors. As you may know, when you press on your brake pedal, this activates a hydraulic pressure which forces small pistons inside your brake calipers to push the brake pads against the...

It is best to keep any fluid system in your car from running dry. The washer system often sits unused, so it can be easily forgotten. When the fierce winter weather is upon us, it is easy to think of...

Hi there. As you already know, replacing components without diagnoses can be expensive and time consuming without resolution. A few things come to mind concerning the lack of performance. First, camshaft timing needs to be checked. When the engine is...

Hi there: Sometimes minor fender bender can trigger other issues to appear, especially if a loose sensor or wire was damaged during the incident. If the engine is making a weird sound while the heater is active, it's possible that...

The steering knuckle is also called steering spindle. This is the steering par that connects the strut and lower ball joint and the steering ball joint so you can steer the vehicle. On some applications the entire steering knuckle needs...

When you suspect a vacuum leak on the engine it may be a cracked hose or a gasket leak. The best way to find it is to use a hose to your ear and move around the engine intake and...