Popular questions

Hello, thank you for writing in. The first task to take on is finding out if the jerking is coming from the engine or wheels. Also keep in mind, even without a check engine light on, there may be a...

Hi, thanks for writing in. This may suggest a short of some kind causing the power to continue to be supplied to the relay. The starter relay is a small unit near the starter that directs power to the starter...

Hi Joy. Thanks for contacting us today. Usually the "click" noise while starting is an indication that the starter motor is either not receiving power to engage the motor. This could be due to a dead battery, damaged electrical relay...

Wiper speed not changing with settings can be caused by a couple of different things. The wiper switch may have broken mechanical contacts or broken electrical circuits internally. Also, the wiper motor may have electrical issues. AN internal resistor may...

Hi there. The motor or switch on the seat has lost power. First check the fuses and see if any of them are blown. If the fuses are good, then check the switch and see if there is power to...

Hey there, thanks for writing in. The canister purge valve is located underneath the throttle body near the front of the motor. If you are unsure how to proceed with the code, a certified pro from YourMechanic can come to...

The key is stuck due to a fault with the ignition switch lock cylinder or the steering column interlock is malfunctioning. To resolve this, you can request ignition switch/lock cylinder repair. Once the stuck key issue is resolved, if you...

You've got a Mustang. You're probably driving and braking pretty fast. The right brakes, on most people's cars always wear out faster than the left ones. This is because when you are driving fast, and when you make a left...

Hi, thanks for writing in. I'd be happy to help. Based on your details, I feel that this could be from a bad cable end or connection to the battery or a shorted battery. I would recommend having an expert...

Hi there. In general, there are two O2 sensors on your Toyota, an upstream sensor (located near the exhaust manifold) and downstream (located after the catalytic converter). Based on the error codes you listed however, it's not 100% certain that...

The problem may not be in the ignition switch but in the transmission shift linkage. Try and push the shifter up into park and turn the key at the same time. There are technical bulletins for the shift linkage causing...

This sounds like a low fuel pressure problem, or an air filter and mass airflow (MAF) sensor problem. Check the fuel pressure and replace the fuel filter first to see if it helps. Next, have the system computer scanned...

This could be just a simple belt adjustment since you have multiple belts on your car. I do not see a belt issue when going into reverse but turning could be the power steering belt is loose. I would recommend...

Hello - I suspect your crankshaft position sensorhas failed. This sensor provides the ignition system with timing information - when to fire each spark plug. This sensor is also the trigger for the tachometer, since it is counting engine revolutions...

The fog lights are controlled through the smart junction box in the right kick panel. The switch signals the box to ground the fog light relay in the engine compartment fuse relay box. The number 58 fuse powers the relay...

Unfortunately, there would be no way to verify what was tampered with without looking at the vehicle in person to see what symptoms the car is exhibiting, and then checking for noticeable changes that are related to those symptoms. It...

If you have the vehicle raised and the lug nuts remove and the rim is stuck on the vehicle then it will take some power kicks to the sides of the rim to break the tire loose. Try to put...

Hello - you don't specific what code is causing the Check Engine light to illuminate (oxygen sensor problem), but a failure of the pre-catalytic converter O2 sensor could cause a Reduced Power experience. Failure of the O2 sensor can cause...

Not really. A lot of it is just scam you know. People aren't stealing by plugging it in your car. First, they have to get in to begin with. The only time something like that happens is with high-end stuff...

Anytime your vehicle goes into reduced power failure mode it is caused by a signal from a sensor is not correct and the engine computer sees a major problem that may be unsafe since it cannot see or operate the...

Blue smoke usually indicates oil getting into the combustion process - not a good thing. If you had your oil changed the day before, check the oil level to make sure it wasn't over-filled. If you car is accumulating some...

Hi Chanel. Since we can't attach images or files on this platform, your best resource is going to be purchasing a service and repair manual for your 2010 Chevrolet Malibu to review the detailed wiring schematic for each mechanical system....

Hi there: After looking into the first error code you posted, the vibration and shaking issues on your VW are most likely caused by a vacuum leak. The P2279 OBD-II code indicates that the ECU has detected a vacuum leak...

Hello. A lot goes on under the hood and many of the components can reach high temperatures. Any fluid leaks coming into contact with these hot components can burn the fluids and cause an odor. An example would be a...

It sounds like you ma possibly have a weak battery or a problem with the alarm system itself. Generally, accessories like alarms will inadvertently set off by themselves when the battery is weak. I would suggest having a professional from...