Popular questions

It takes "roughly" 8 hours but if you have the Xdrive version, add 2 hours. The cost depends on exactly what you want. A new transmission? A used transmission? A rebuilt transmission? The recommended approach is to install a rebuilt...

The diagnostic service fees are not included in the service call. If a diagnosis is needed to find out the problem then the mechanic needs to be compensated for their time to do the diagnosis service.

There are two ways to unlock one of the car doors without a key: 1. From inside the vehicle, pull the door handle to open the door. This will automatically unlock the door, and open it. This feature only works...

A logical first step is to have the battery load tested and, at the same time, measure the output of the charging system to determine if the charging system is functioning. If the battery fails the load test (OR only...

You would need to check the temperature sender unit to see if it got coolant in the connector or wire got shorted somehow. Disconnect the sensor and see if the gauge acts differently. If it does then replace the sensor...

Hello, thank you for writing in. The vehicle may be having issues with the electric power steering module and system. Luckily there is a check engine light on, which means there is an engine diagnostic code that has been set....

Hi - with the water you see under your vehicle and the grinding noise is a good indication that your water pump needs to be replaced. The grinding noise is the bearing starting to fail. Trembling and shaking while braking...

This is most likely the result of a clogged windshield wiper nozzle. Try blowing compressed air through the nozzle or cleaning the head of the nozzle out with a pin. Try tracing the washer hose from the nozzles back to...

The grinding noise could originate in the drive train, including wheel bearings, or could even be in an accessory drive. From your description, the noise is probably distinct enough that a certified mechanic could pinpoint the origin upon inspection. If...

It sounds to me like the return spring may be to blame here. Try pulling back on the pedal while pulling the release handle. If it still wont move, look and make sure the release handle is pulling the release...

Hi...it requires 1.4 hours to remove and replace all spark plugs on the 3.6L. If you desire that the spark plugs be replaced by a certified Mechanic, dispatched by YourMechanic right to your location, please request spark plug replacement and...

Hello, and thank you for writing in. The first thing we need to determine is if there an issue with the latch, the switch, the key fob, or possibly the wiring. The best way to determine this is to test...

Sent to CS. Hi there. Replacing a lower radiator hose on your vehicle can take up to 50 minutes at a shop. Most shops will charge for replacing the hose and filling the radiator as 2 separate service times. This...

Hi there. It's possible that you have a speed or wheel sensor that has been damaged during your accident. Typically this will cause the light to stay illuminated until it is replaced. The best way to diagnose this issue correctly...

Hello. It is possible to remove the rear seats, however, they would need to be uninstalled completely. The rear seats are bolted down and have electric motors built into them so removal would require tools. If the QX60 does not...

The harnesses are referred to in GM parts catalogs as "body wiring" and "rear lamp wiring". However, the correct wiring harness for your vehicle can only be found via a VIN number search in the catalog. It can't be searched...

The purge valve is mounted on the engine and you will see hose connections from the valve to the intake manifold as well as a wire harness connection. The purge valve should be tested to determine if it is actually...

Faults with the mass air flow sensor do not cause noise. The noise could be due to exhaust leaks, or internal faults in exhaust components such as the muffler or resonator if equipped. Belt driven accessories can be the source...

the most common cause of a belt breaking or coming off is the belt tensioner seizes and throws off the belt. Have the tensioner and belt replaced. Check all the other pulleys are free moving and not seized.

If you are getting a very high idle when you first start the car and it comes down to a normal idle in less than five minutes, then you may have a vacuum leak in the intake manifold gasket that...

Hi there, The Honda VTEC system relies on two main electrical components to function properly. One of these components is the VTEC oil pressure switch which tells the engine computer that the oil pressure is sufficient for VTEC operation. The...

Hi, thanks for writing in. I recommend checking the brake fluid level and the brake fluid level sensor. These are more "logical", given recent service. Replacing the ABS is an expensive proposition. I would get an ABS reader on it...

Hello. Your rear view mirror should have its own adjustment completely independent of the seat adjustment. I would refer to your owner's manual for specifics on where the rear view mirror controls are located and how they function. Consider taking...

Hi There, This may be related to a dirty or faulty mass air flow sensor or possibly a dirty or faulty idle air control valve. The idle air control valve monitors the air intake as it is mixed with fuel...

Depending on what fuse you are referring to, this may impact whether or not the car will start. There are a number of relays that will affect the ability of the car to start such as a starter relay, a...