Hello, the first thing to do is check the oil level and get that correct and then diagnose the overheating concern. It will probably need to be jump started to get it going. The cause of the overheating must be...
If you have just installed a new fuel pump and can not hear it come on when you turn the key to the run position (not the start position), you may have a ground issue. You can also perform a...
As always, the first order of business is to confirm the diagnosis. If the Mechanic showed you "looseness" in those parts, that's fine but "a" concern is whether or not they are giving you "assurance" that once those parts are...
This is not an error. The crank shaft goes around two times to the distributor one time. This means if you put the number cylinder on the compression stroke top dead center and line up the distributor then if you...
Hi and thanks for contacting YourMechanic. First, with the dirty cooling system, you would need to perform a coolant flush and replace the thermostat and radiator cap. This will help with the overheating issue if you are still experiencing that....
Hello, thanks for writing in about your Buick Rendezvous. From what you've described, you most likely damaged the transmission. You will need to take the vehicle to a transmission mechanic to fix this particular issue. If you'd like a second...
Hey there, thanks for writing in about your 1993 Chevrolet K1500. Keep in mind that just because the fuel pump runs does not mean it produces enough pressure for the fuel injection of the engine. Have the pressure tested to...
If the issue began after you replaced the wiring I would double check the wiring for any faults. A continuity test would be the best way to make sure that the connections are secure and making proper contact. If the...
Most Check Engine Lights are illuminated when an error code is triggered and stored in the ECM. Even if you've repaired what was broken or damaged, you still need to clear those codes in order for the light to go...
As for the performance of the vehicle, the engine will likely run just fine with minimal differences. However, it is possible that installing this oxygen sensor could cause your Check Engine Light to come on. I would recommend looking in...
The first concern is whether you could have an exhaust leak or a fuel leak. If leaks of that type exist, they should be repaired as both are safety hazards. Occasionally, just due to the weather, exhaust fumes can get...
Hello there, loosing oil can become a big problem with your 2010 Nissan Micra if left unattended. If no visible leaks are seen than you are correct the oil is most likely being burned. When oil is burned there are...
High mileage engines leak oil into the combustion chamber through worn out valve stem oil seals, worn valve guides and ill fitting piston rings. If a substantial amount of oil is entering the combustion chamber the plugs will quickly foul....
Hi there. Chances are the latch assembly is either faulty or the lever linkage has become detached. The door panel will need to be very carefully removed from the inside and the latch and linkage assessed. If the latch is...
You have great diagnostic skills! In addition to the components you have listed, it's also possible the air line to that corner has a leak, or the solenoid itself has a leak. Unfortunately, this is a chronic problem with model...
Hello. If the engine will crank over and it will not start after it has run for a while then most of the time this is caused by a failing carburetor. Most of the time it will flood out and...
This condition is commonly caused by defective spark plugs, wires or ignition coils and occasionally all 3! Service Bulletin number #SB-10250 addresses this issue, and in most cases if you’re under warranty the dealership will replace these items free of...
Hi there. A turbocharger is is divided into two sections: the turbine and compressor. The turbine is attached to the exhaust manifold and is driven by exhaust gas pressure. The turbine is connected by a shaft to the compressor. The...
In order to properly test the system you will need to hook up gauges and check the pressures to see if the low side is getting low enough psi to cycle the compressor. Check if it is getting bellow about...
Hello and thanks for writing in. As you may know, there are a number of things that can cause a transfer case to fail, such as failing U-joints, a bad transfer case output shaft seal (resulting in trans fluid leaking...
The broken wire is to the wheel speed sensor as part of the antilock brake system. Depending on the other damage that is done you should be able to drive it slowly. The clunking is the wheel speed sensor is...
We would need to know the exact code your vehicle is setting. The code should have a complete pinpoint test done to locate the problem. Once the tests are done, then the system can be fixed. Driving the vehicle with...
In order to determine if your three wheeler has any issues, I would recommend having the vehicle inspected by a qualifed technician who specializes in off road vehicles such as this. They are specially trained to diagnose and repair off...
