Q: Stalls when shifting into gear and low idle

asked by on January 31, 2017

what could be wrong... any advice would be great....

This may be a sign of a faulty MAP sensor as the vehicle responds adversely to a load put on the motor (i.e. putting it in gear or engaging the brakes). The Manifold Absolute Pressure (MAP) sensor senses engine load and generates a signal that is proportional to the amount of vacuum in the intake manifold. The engine computer then uses this information to adjust ignition timing and fuel enrichment. When the engine is working hard, intake vacuum drops as the throttle opens wide. The engine takes in more air, which requires more fuel to keep the air/fuel ratio in balance. When the computer reads a heavy load signal from the [MAP sensor]((https://www.yourmechanic.com/services/manifold-absolute-pressure-sensor-map-sensor-replacement), it adjusts the fuel mixture to slightly more rich than normal so the engine can produce more power. The computer will then retard (back off) ignition timing slightly to prevent detonation that can damage the engine and decrease performance. This may also be caused by other closely related components such as a dirty or failing mass air-flow sensor, a faulty throttle position sensor or potentially a vacuum leak. I would recommend having an expert from YourMechanic come to your location to diagnose and inspect your vehicle.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing

What others are asking

I put the wrong key in my car and a few weeks later my car just shut down and it will not start I believe it's the computer but...

Hi there. What had happened is the wrong key set the security to the vehicle. This is to prevent the vehicle from starting with the wrong keys. Try removing the battery cables (+) and (-) for 13 minutes. During that...

Clunking noise that chages relative to changes in speed

Noises are best diagnosed firsthand, however, I can provide some guesses in regard to your noise. The first thing that comes to mind is a failed CV axle, which will often make a clunking noise upon acceleration. A worn propeller...

Battery runs down in two days if the engine is not running. The alternator has 14 volts.

Hi there. It seems that there is a parasitic load on your vehicle's battery when the vehicle is sitting and not running. Check the battery for a voltage and see if the charge is 12.6 volts. If the battery is...

I have a 2007 Chevy Impala...battery saver active mode

Hi There, This can be caused by a loose battery cable which is often times the problem. Try checking to be sure they are connected properly. Also, there is a sensor that has 3 small wires running to it that...

when car is running, squeaking is coming from the right side of the car when idle

A quick diagnostic can be performed by simply taking all of the belt driven accessories out of the picture by disconnecting the drive belt(s) and then very briefly running the engine. If the sound disappears, the faulty component is then...

Car won't pass smog.

Hello! I will be happy to assist you. On your particular vehicle, random misfires are commonly caused by things such as low fuel pressure, a faulty oxygen sensor, bad vacuum lines, or faulty air flow sensors; a broken or loose...

Engine hot, difficult shifting, shutting off

Hello there, thank you for asking about your 1987 Oldsmobile Cutlass Calais. A common problem that can cause stalling is a stuck torque converter clutch. This device connects the link between the engine and transmission, but should slip some when...

How do I use the power folding mirrors?

The power folding side view mirrors can be folded inward to decrease the size of your car. This feature should be used to help you fit your car into tight spaces, or as a safety feature when driving through an...

Car sputters and shakes below 1500 rpms especially

There is a common problem with this specific year and engine of VW TDI's. The camshaft material is not hardened enough, which leads to abnormal wear of the lobes and damage to the lifters. The fuel injectors are also controlled...

Related articles

How to Become a Certified Mobile Vehicle Inspector (State Car Inspector Certified) in Massachusetts
Automotive technician jobs include mobile vehicle inspectors. Learn how to do car checks in Massachusetts take an online inspector initial training.
How to Get a Car Loan When You Have Bad Credit
A A few financial missteps can greatly impact your credit score, and it is far more difficult to repair bad credit than it is to gain it. If you have managed to be branded with a poor credit score,...
P2544 OBD-II Trouble Code: Torque Management Request Input Signal A
P2544 code means an input signal malfunction has been detected in a powertrain-related control module due to problems with electrical input signals