I just got new tires for my 1995 GMC Sonoma. They rub sli...
Responses
ShawnS1113
234 days ago
Hello, my name is\*\*\*\*\* am going to help you with your question. Everything you have listed is the same as stock except the hub bore is 70.3, that difference should matter
Customer
234 days ago
then I need to keep looking for something that is exactly 70.3 hub bore?
ShawnS1113
234 days ago
No, the .2mm should not matter, the difference is negligible
Customer
234 days ago
Ok got it. I am also looking into a 2" suspension lift. Will this add more clearance or should I go with a body kit?
ShawnS1113
234 days ago
That is really up to you, just be aware that [tire size](/topics-tire-size/) changes, wheel spacers, and lifts are all changing the geometry of the truck and it is most likely things will wear out faster
Customer
234 days ago
sir. Now, I did find the other day that my oil cooler lines (significantly) are leaking at the oil filter and at the radiator (very slight). I have been advised to change these before doing anything further to the wheels/suspension for safety reasons. However, even with a floor jack, I cannot get enough clearance to get under the truck to change the lines. What would your advice be?
ShawnS1113
234 days ago
You are going to need to get some truck jack stands
Customer
234 days ago
Got it. I just ordered the spacers. I will advise on hey they work out!
ShawnS1113
234 days ago
Sounds good, if you need anything else please let me know and have a good day
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
Poor quality door handles falling apart
The material from which manufacturers make the chrome can be sharp, causing injury as it peels off. The safest and most effective means to prevent further harm is to replace the handles. Being that your car is a 2010 and...
Steering wheel shakes at speed over 80 mph, after tire replacement
There are several options you could try to test this issue. One option would be to have your tires checked for a possible manufacturer defect. This would be something like a slipped belt that would cause a bump in your...
Car isn't cranking
It sounds like you may have a problem with the battery cables (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-battery-cable). Check the ends by the battery thoroughly, especially if they have been replaced by universal ones. The main ground cable runs with the starter positive cable and...
I can hear the fan of the car turning on often, could that indicate serious engine problems?
Hi, thanks for writing in. Newer vehicles, such as the Cruze, run hotter for greater fuel efficiency. It also means the engine is running closer to "maximum" temperature more of the time, which included running the auxiliary electric fan more...
Engine idle fluctuates
You may have a dirty or failing idle air control valve. The idle air control valve reads the air intake as it is mixed with fuel prior to being injected into the engine at low speeds and at idle. Since...
how hard is it to replace ac compressor on 2011 sonota
The first step in replacing the A/C compressor is to remove anything that blocks access to the serpentine belt. Once this has been done, the next step is to remove tension from the serpentine belt and slide it off of...
Charging system warning light.
This may be a sign of a weak battery or a failing voltage regulator. As you may know, the alternator is responsible for charging the battery while the engine runs by generating amperage and recharging the battery while the engine...
Tire making loud thumping/knocking noise
Hello. You may have a wheel bearing going bad or flat spot on your tire. I suggest that you have a technician such as one you can choose from YourMechanic perform a suspension evaluation on your vehicle to help you...
White smoke coming from engine after car is turned off
Hello, thank you for writing in. The symptoms you are having are classic of a failed head gasket. While it can be expensive and time consuming to check the condition of the new head gasket, it is very possible it...
Browse other content
Cities
Estimates
Maintenance
I just got new tires for my 1995 GMC Sonoma. They rub slightly on the frame when the wheel is locked in a turn. I am going to get spacers, but want to make sure that I get the correct size. The specs on the spacers are: Wheel Bo...
I just got new tires for my 1995 GMC Sonoma. They rub slightly on the frame when the wheel is locked in a turn. I am going to get spacers, but want to make sure that I get the correct size. The specs on the spacers are: Wheel Bolt Pattern: 5x4.75 Hub Bore: 70.5mm Thread Pitch: 12x1.5 Will these fit as needed?