Q: Do you service 38135 zipcode

asked by on May 05, 2017

Do you service 38135 zip code?

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing


Experienced Mechanic?

Earn up to $70/hr

What others are asking

How do I clean the leather seats?
The leather seats in your truck are of high quality. To maintain their high quality, proper cleaning is necessary. To clean the leather seats. Clean up spills and stains quickly. Wipe the surface of the seats with a soft, damp...
My temp gage barly goes past 130
The thermostat most likely is stuck open and would cause the engine to run too cold all the time. It may eventually get to operating temperature but the engine will run richer until the temperature gets above 180 degrees. I...
I recently changed my cabin air filter and I saw more noise from the engine. Why does this happen?
Hi there. The noise you're hearing may not be engine noise. You may be hearing debris being knocked around the blower motor. The debris may have fallen into the blower motor when you changed the cabin filter (https://www.yourmechanic.com/services/cabin-air-filter-replacement). Remove the...
How can I know the exact motor I need to buy for a 2005 Honda Odyssey
Hi there - the engine in your Odyssey (and newer than 2005 Odessys) is a Honda "J35A7" engine code, 3.5 liters displacement. Make sure your supplier source documents that you are getting this specific engine model for compatibility. The engine...
How do I disable /remove onstar system from my truck
Hi there: You should contact your GMC dealership to ask about this, as their ONSTAR program and accessories are often tied into the ECU and could impact the overall operation of some security features on your Yukon. Cutting wires without...
Steering wheel doesn't return back to the center
Hi there. The condition you are describing is often a symptom of a steering column failure. The steering column is comprised of several individual sections, starting at the steering rack, and continuing to the steering wheel itself. Sometimes on newer...
Why would my 4x4 high and low light flash three times when start up and driving in my 2002 Ford Explorer
Hello. Most of the time when this is occurring it is due to an electrical issue with the 4X4 system. I usually remove all of the connections at the transfer case and clean them and add dielectric grease. That may...
i upgraded from 28.9 in tire to 32.4 in tires. a week later transmission went out, what should i change to relieve strain on trans
The change in shift points generates added heat in terms of operation. Increasing the tire tire diameter more than a percent or two affects the transmission shift points, as the shift points were programmed based on the vehicle's original tire...
on a chrysler 200 the airbag light goes on and off for Driver. Is there a way to get it to stop or disable?
Hi there. In most cases, the airbag light will go on or off if a sensor is damaged or has a loose connection or fitting. Unfortunately, it's a safety system that can't be disabled. It's probably a better idea to...

Related articles

How Long Does a Cruise Control Switch Last?
The The cruise control switch is mounted on the steering wheel of your vehicle and is intended to make driving less strenuous. Once you choose a speed, you can depress the cruise control switch, and your vehicle will stay at...
P0746 OBD-II Trouble Code: Pressure Control Solenoid Performance or Stuck Off
P0746 code means the PCM has detected an irregularity in the electronic pressure control solenoid circuit often due too blockages or low fuel levels.
P0960 OBD-II Trouble Code: Pressure Control Solenoid A Control Circuit/Open
P0960 P0960 code definition The P0960 code is a generic powertrain code related to the transmission, including pressure faults and sensor failures. In this case, the engine control module (ECM) has received a signal noting that the pressure control solenoid...