Showing articles & questions for topic
p0017

It could very well be a timing chain problem (https://www.yourmechanic.com/services/timing-chain-replacement). The P0016 and 17 indicate that the camshaft sensors (https://www.yourmechanic.com/services/camshaft-position-sensor-replacement) are sensing the camshaft in a position that does not logically correspond with the crankshaft. The P0302 (https://www.yourmechanic.com/article/p0302-obd-ii-trouble-code-cylinder-2-misfire-detected-by-jamahl-walker) and P0355...

With the code P0017, the crankshaft position sensor is not picking up the engines speed properly. Check the following areas for any issues to fix your P0017 code issue. Check the following: The timing chain could be stretched The timing...

Of course, after a repair be sure to erase the codes. If the same codes do return after erasure, then there is a continuing, unresolved problem. Diagnostic Trouble Code P0016 (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) and Diagnostic Trouble Code P0017 (https://www.yourmechanic.com/article/p0079-obd-ii-trouble-code-crankshaft-position-camshaft-position-correlation-bank-1-sensor-b-by-jay-safford) have multiple causes...

Hi there. These codes (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) lead me to believe that the cam/crank timing is out. However, there are possible underlying problems that can set the same codes and give you the symptoms you're describing. You could have a wiring/connector issue...

Hello. If the oil level was low, then it will cause these codes (P0016 (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) and P0017 (https://www.yourmechanic.com/article/p0079-obd-ii-trouble-code-crankshaft-position-camshaft-position-correlation-bank-1-sensor-b-by-jay-safford)) to appear. The variable valve timing system on this vehicle is controlled with oil pressure so when the oil level is low...

Hi there. There are a few different things that can cause this. Most of the time though, this is caused by an issue with the TCM or a power issue to the TCM. I usually start by testing the ignition...

As you may have already learned, the code p0017 (https://www.yourmechanic.com/article/p0079-obd-ii-trouble-code-crankshaft-position-camshaft-position-correlation-bank-1-sensor-b-by-jay-safford) indicates an issue with the crankshaft position sensor. This would mean that that transmission doesn't understand the speed and can't send the same information to the transmission. I don't think...

Diagnostic Trouble Code P0017 (https://www.yourmechanic.com/article/p0079-obd-ii-trouble-code-crankshaft-position-camshaft-position-correlation-bank-1-sensor-b-by-jay-safford) has many causes other than a failed position sensor. For example, the valve timing could be off if the timing chain has jumped, there could be oil flow problems to the phaser from incorrect oil...

Hello. The variable valve timing and the camshaft position sensor are two separate sensors. The camshaft position sensor is more towards the front of the engine and is a lot easier to replace. The variable valve timing sensor is a...

The codes P0016 (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) and P0017 (https://www.yourmechanic.com/article/p0079-obd-ii-trouble-code-crankshaft-position-camshaft-position-correlation-bank-1-sensor-b-by-jay-safford) are related to the crankshaft location and the camshaft location. Check the camshaft position sensor and see if its plugged in. If the wiring harness is in good shape and the wires are...

Hello and thank you for contacting YourMechanic. Most likely you have a loose connection or a sensor is failing. Check the crankshaft position sensor (https://www.yourmechanic.com/services/crankshaft-position-sensor-replacement) and the camshaft position sensor (https://www.yourmechanic.com/services/camshaft-position-sensor-replacement) for any damage and make sure that they are...

Hi, from what you’ve described and the nature of the two codes, it sounds like a timing problem. It’s possible that the timing chain has stretched, the timing chain tensioner needs to be replaced, a timing chain guide has slipped...

Most of the time, replacing the components that you did will take care of the P0017 code (https://www.yourmechanic.com/article/p0079-obd-ii-trouble-code-crankshaft-position-camshaft-position-correlation-bank-1-sensor-b-by-jay-safford). Lack of oil flow to the actuator can contribute to the code. Also, using motor oil that has a different viscosity rating...