Q: can't find crank sensor on VW CC 2010... any ideas?

asked by on August 16, 2017

I have a turbo VW CC 2010. check engine light is on and it's giving a cam/crank sensor code. I changed the cam but I cannot find the crank sensor anywhere. Any ideas of pics?

My car has 105000 miles.
My car has an automatic transmission.

The crankshaft sensor is on the side of the motor near transmission directly in line with the starter on side of engine block.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing

What others are asking

Engine shuts off when going over a bump.

Hi there. There is a loose ground wire on your vehicle that is moving around when you drive over bumps. Check all of the ground wires to the engine and the battery and tighten any wires that are loose. If...

My clutch is not working.

Go under the vehicle and see if the return spring has came off the slave cylinder on the clutch assembly. If the return spring is there, then look to see if the slave cylinder is pushed all the way out....

Clicking noise in the engine, been going on for a while

Your truck most likely has an internal engine issue that is just starting to present itself. Abnormal noises, whether from your refrigerator, engine or even your plumbing can be an indication that repairs are needed. In the case of your...

Why would i keep getting p0013 and p0023 codes when the truck isn't equipped with exhaust cams, it's not a 4 cam engine

Hello - this engine, although single overhead camshaft, does use variable cam timing, actuated by "cam torque", rather than engine oil pressure, to adjust exhaust valve timing (relative to the intake valves). This engine was introduced to Ford trucks in...

Fuel fill inlet

Hi...thank you for your question and I will try to help you with the issue. ALL faults that cause the check engine light to illuminate have to be resolved, with the light ultimately extinguished, because once the check engine light...

Tapping noise when under a load.

Hi there. The sound that you provided for the tapping noise sounds as if your engine is dieseling when operating. This is a noise that occurs when the engine is either running too hot or has too much carbon on...

Check engine light on , 2012 Hyundai Sonata

Hello, a common issue with Hyundai engines is the camshaft and crank shaft position sensors failing consistently. These sensors detect where the camshaft and crankshaft are in relation to each and when they fail, the vehicle usually goes into limp...

I was looking for the location of the crankshaft /camshaft sensors on my 2012 audi a7 3.0.

Hi there. The crankshaft position sensor is located on the back of the engine on the driver side near the top at an angle. The camshaft position sensor is located just behind the camshaft gear on the left bank cylinder...

Hi, I have a 2003 bmw X5 3.0i petrol. 2 problems. 1. abs trifecta lights on, when i plug in my own (cheap) diagnostic tool it onl

Hello and thank you for contacting YourMechanic. The code for your BMW P1619 is referring to the thermostat sensor. Check the thermostat sensor harness for an debris, looseness, and corrosion. If the sensor looks good, then the thermostat needs replaced...

Related articles

Symptoms of a Bad or Failing Manifold Temperature Sensor
Common signs include a rough idle, lack of power, high NOx production, and emissions test failure.
A Buyer’s Guide to the 2012 Volkswagen Routan
For For those who need a vehicle that focuses on people-moving and little else, the 2012 Volkswagen Routan just might hit the mark. With improved fuel economy and responsiveness compared to the Chrysler platform on which it is based, this...
Can a Bad Sensor Prevent a Car From Starting?
If your car isn't starting or has a hard time starting, a faulty sensor may be to blame. Car sensors monitor data to keep your car running smoothly.