Popular questions

Hi there: The P1095 ODB-II trouble code indicates that the O2 sensor signal circuit is slow switching from lean to rich (Bank 1 Sensor 1). When this occurs, it can cause your vehicle to stall rather quickly. However, before you...

The BCM or body control module controls all of these items and there is a technical bulletin to get the BCM reprogramed. The reprogram should fix the issue for you. The dealer will have to do the reprogram for you....

Hi there. The P2135 OBD-II error code indicates that the Power Control Module (PCM) has detected an erroneous reading regarding the voltages transmitted by throttle position sensor A or B, the accelerator pedal position sensor and or the actual throttle...

P0604 is an internal memory error in the ECM. It will need to be replaced. It may be possible to get a pre-programmed ECM for you to put in, but this would be a question to pose to your local...

In this case you should have an experienced technician look at the vehicle. Limp mode is usually a term used for a vehicle with an automatic transmission which stays in second gear when certain faults arises. A certified technician, like...

P0013 sets if there is an open or short in the circuit to (and from) the exhaust camshaft oil control valve. That valve is an actuator or solenoid controlled electro-mechanical device. The underlying fault that caused the code to set...

Hello there. This sounds like a more unusual situation. Ford uses the rollover stability control system as an additional safety feature to help prevent rollovers. A bit of body movement in normal wind speeds would not be abnormal. It should...

Hi there, Chances are the brake light switch is faulty. My advice is to have a mechanic, such as one from YourMechanic, diagnose and repair the brake light switch circuit. Fuse 14 can be removed when the car is not...

The remote keyless entry transmitter battery usually lasts for a few years. If the battery dies, you can easily replace it by following these steps: 1. Use a narrow tool to pry open the center cover of the transmitter. 2....

More than I can remember--a whole bunch of them. Putting in the wrong oil generally doesn't make them blow up. It might make it wear a little bit longer or run a little harder or colder, unless you put in...

If the ABS light is on, there will be diagnostic codes to access. Those codes will provide enough clues to dig into this. I would first obtain those codes simply because they will give a direct indication of what components...

Hello. If the shifter cable is popping off of the transmission selector sensor, then either the end of the cable is worn out or the selector is bad. Most of the time the cable end is where the problem is...

Hello Sal, the timing cover gasket would be replaced and included in the estimate with the timing belt. There may be a timing belt kit available which would include coolant pump, gaskets and drive pulleys. Another recommendation would to replace...

This is typically what occurs when the window motor or regulator fails. Most of the time, it is the motor. The motor could have already been getting weak, and when this occurs the motor can lower the window because it...

Vibration between shifts in an automatic or manual are pretty similar and are usually caused by loose motor or transmission mounts, but could be mimicked by suspension components. Have a mechanic from YourMechanic inspect your vehicle for any looseness in...

Hi there. In short - yes; maintenance costs on BMW's are above average. With 100,000 miles on the vehicle, it's likely that you'll have to budget for possible major repairs in suspension, transmission and oil seals and gaskets that tend...

If the switch is on the exterior of your vehicle, yes. You have a number of switches located all over your vehicle. Those switches control the circuits for the power windows, power door locks, sunroof, seat warmers, stereo, and many...

A mass air sensor with low output voltage may cause loss of power, hard starts or rough running.

I looked up the two applications. Those two engines use completely different castings for both the heads and the block and the flywheel (flex plate) is different as well which will make it incompatible with your transmission. If you search...

Hello. If the 4 wheel drive is not engaging, then there is typically a problem with the transfer case electronics. The most common cause on your vehicle is a bad connection on the transfer case. I would typically remove the...

Hello there, many issues will cause your 2004 Saab Turbo to have a steering lock malfunction with a fault code that will not clear. Without knowing what the fault code is I can only offer general advice. When the code...

Engine stalling while driving is typically caused by a problem with the ignition system. Plus, the fact that you can restart the vehicle after cycling the ignition leads me to believe the problem is electrical. The first thing I would...