Popular questions

Billing question was sent to CS for the cost of replacing the valve cover gaskets on a 2006 Infiniti M35 with a V6-3.5L engine.

Diagnostic trouble code P0075 means there is a fault in the Intake Valve Control Solenoid Circuit. A defective solenoid is one possible cause of the code setting but problems in the circuit wiring are often the cause of the fault....

If both the starter motor and fuel pump are not working be sure the Engine Immobilizer is not active. If you are sure the security system is off and yet power does not reach the fuel pump or the starter,...

Hello there. To request an estimate to have your water pump replaced, please click this link to the service page. Once you get to the page, click the blue Get a Quote button to request an estimate.

Hi Barbara. There are several individual components that make up the charging system and can trigger a battery light to illuminate. Some of the most common parts that trigger a warning light, including the voltage regulator, one of the multiple...

Hi there. Typically these codes are caused by an exhaust leak, clogged injectors, or intake vacuum leak. If problems just happened to start after getting fuel, then you may have a purge valve leaking excessive fumes into the intake when...

Hi and thanks for contacting YourMechanic. The problem might be with the crankshaft position sensor being effected by heat. This can be verified by measuring the resistance of the crankshaft sensor with a digital volt ohm meter (DVOM) and then...

This is a common sign of a faulty starter solenoid. The starter solenoid is located on the starter and has internal electrical contacts that transmit electricity to the starter. When this fails, it may cause a clicking sound and will...

Hello, thank you for writing in. The passenger (right) side of the vehicle (on yours and a lot of other vehicles) holds a computer system behind the fender (just under the floorboard). This is the box that controls the power...

The tab on the bottom of many rear view mirrors is what is known as the "day/night" adjustment switch. The daytime setting is with the tab pushed toward the front of the vehicle. You should be able to see normally...

A code to an O2 sensor can mean the sensor is having a problem or the sensor is telling you that there is a problem with the fuel control system. Depending on the code received your engine is either running...

Hi There! It sounds like you may have a dirty or failing idle air control valve causing your engine idle to fluctuate and eventually stall. In the mornings it is normal for the engine idle to be a bit higher...

Hi there, thanks for writing in about your 2003 Alero. If the engine is turning over when you turn the key, then it is not the starter, but it may be the fuel pump or ignition module and coil. Check...

When the reverse light switch was replaced and the fuse burns instantly when the reverse lights come on, then there is a direct short with the reverse light circuit. Check all of the wiring from the reverse light switch to...

Hi and thanks for contacting YourMechanic. Put a manifold set (A/C gauge set) on the A/C ports and check the system when it is running on high A/C. Look to see what the pressures are on the high side and...

The anti-lock brake system (ABS) Warning Light is located on the instrument panel. When this light is illuminated, it means that there is an issue with your ABS. Since the ABS is a key part of your brake system, you...

You should check for any codes that could be stored in the ECM (computer) as the check engine light is on. This will give you a starting place to check for the condition that you are having. Since the vehicle...

As noises, scraping and knocking often have different causes so it is not clear if there is just one issue or multiple issues with your car. In general, if these noises are coming from the chassis or suspension, the possibilities...

Q: How do my turn signal lights cancel on their own? Most vehicles are designed with turn signals that operate in a manner that allows them to return to their default position automatically, via a mechanism built into the...

Hello. From what you describe it would appear that your vehicle is experiencing more than one problem. If the pump and AC blower motor are bad then they will need to be replaced to restore functionality to both systems. The...

Hi there: In most cases when the serpentine or drive belt keeps breaking it's due to one of three issues. First, the belt is either too tight or too loose when it's installed; which is typically caused by a drive...

You have two hood support gas charged shock supports that when they are weak and low on charged gas will not support the trunk lid as it should. You need to replaced both sides.

Hello. Yes it is likely that there was a fuse blown when installing the battery. The fuses that are of the most likely concern are F21,F40, F9, and F5. I recommend checking the wiring under those fuses as well. It...

Hello. The issue may not be incredibly complex or major. With newer vehicles being equipped with more complex diagnostic systems, it is not uncommon for one issue being related to two separate warning lights. The first step is to have...