Popular questions

Hi there. What could be the issue is the main valve to the transmission may have disconnected from the shifter lever on the side of the transmission. Raise up the vehicle and put it on four (4) jack stands. With...

Misfire codes can be caused by a range of failures. Spark Plugs, Coils, Injectors, Manifold gaskets could all be suspect. When the check engine light is on and the car has stored codes, your first reaction is to replace the...

Hi there. Before we assume the root cause of the problem, there needs to be a proper diagnosis performed. There is nothing more costly than replacing parts that are not needed or a misdiagnosis resulting in unnecessary parts being replaced....

Hello there, thank you for asking about your 2007 Chevrolet Cobalt. If you jump the fuel pump relay and still do not get fuel pressure, then you may have wired the fuel pump in backwards. The pump may be running...

Yes, 16 mpg is very low for a Kia Rondo, especially with the amount of highway driving you do daily. Start with basics like the air filter and tire pressure, which are two big items that will rob you of...

Hi. The belt tensioner pulley may need to be replaced if it is chirping. The chirping noise comes from the bearing inside the pulley that is worn out. It is typical for them to be replaced along with the serpentine...

After the HomeLink system has been set up, it is ready to use. All you have to do is press the corresponding HomeLink button on your overhead console, and your garage door will open or close. Tip Even after programming...

With all most 200k miles you most likely have all four mounts needing replacement. The first thing to do is to physically look at each one and look for rips or tears in rubber, sagging or oil soaked. Once all...

The best thing to do is to have your cooling system checked to find the cause of the broken tube. The system may have other issues that would need addressed at the same time. That being the case, I recommend...

It sounds like you are experiencing a lean condition and engine pinging. The most common fault I have seen for this is when the mass air sensor causes the engine to go too lean. When you look at the scanner...

Hi. This usually means there is a problem with the wiper transmission being worn-out or the place were the wiper arm attaches is worn-out, too. The wiper motor turns the wiper transmission, which allows the wiper blades to wipe the...

If your airbag light is on then your airbag system is disabled and would not deploy if in an accident. The airbag light coming on needs a technician to scan for codes and diagnosis of the code or codes received....

Hi Glamy. You really need to have the dealership reprogram the locks and your existing FOB key in order to disable the missing key. That's really the only way to correctly do this.

Your engine design is of the "interference" type. That means that if the timing belt was not installed correctly (or breaks when the engine is running) and thus the camshaft(s) turns out of synch with the crankshaft, the valves can...

Hello. Unfortunately it sounds like you may have replaced some parts that may not have been needed. The most common cause of this noise on your vehicle is the front struts and the front stabilizer link pins. I start by...

Hi there. The issue seems to be that the fuel level indicator sending unit is not working properly. When your fuel gauge is reading at a 1/4 tank, it maybe at 1/8 or 1/16 of a tank causing the fuel...

If the paint is chipping on the front of the car or behind the tires on fender it may be caused by bugs or small rocks or gravel and you will need to have a auto body paint shop repair...

Hi there. If the code came on for the camshaft position sensor, then the computer has seen that the sensor is not working properly. If the vehicle was working before and now has the code for the camshaft position sensor,...

Hi and thanks for your question. Sounds like there could be a fuel or spark issue with your engine. First you would need to scan the computer for what the engine light code has stored to have a starting place...

If this happened right after the work was done then you either have a leak in the system that allowed the refrigerant to come out or there is an electrical issue. It is possible that this was overlooked if the...

Hi Andrea. Thanks for contacting us today. To be honest, if at all possible, none of these products should be used to fix a flat tire. Essentially, both products work by introducing a chemical formula to burn the inner lining...