Popular questions

The first issue to deal with is the part number. Are you sure the part is correct? To reduce diagnostic headaches, and post-installation problems, it is best to buy the OEM sensor from a Hyundai dealer. If you have the...

Hi there. A check engine light or other warning light is triggered, it is due to an error code being stored in the ECU of your Subaru. The error code can be caused by a sensor recognizing a mechanical or...

The oil leak may be coming from a leaking oil drain plug or another gasket or seal of the engine. The inlet tube is very important: it seals out the dirt and debris that the filter cleans out of the...

Hi Sahil. Thanks for contacting us today. If the clutch plate alone was replaced, it's possible that either the clutch is not correctly adjusted or the faulty component is something different. It's best practices to replace the entire clutch pack...

A ticking that changes frequency in line with engine RPM can be an indication of a collapsed lifter. Replacing a lifter requires a good amount of the upper engine to be taken apart to swap it out. It is hard...

There are a number of things that may cause the vehicle to stall while driving. This can happen for any number of reasons such as fuel supply issues such as a bad fuel pump, vacuum leaks, electrical faults or various...

Claimed by Blake Griffin

Glad to help you on this. Yes, if the turn signals are not working, even as the bulbs are OK, there is definitely an electrical problem. A certified technician, like one from YourMechanic, would simply trace the circuit until the...

Hello. I can only suggest you transfer the parts from the new pump to the old housing. If the parts look the same, it should work. To get tank size and year you would need to find the part number...

The lightning bolt warning light alerts you to a fault in the electronic throttle control system in your vehicle. This may be a faulty throttle body, the throttle body sensor or possibly the throttle body control motor which is what...

Hi Mike. Thanks for reaching out today. In most situations, a problem like this is caused by one of two things; either the brake master cylinder is malfunctioning (which is causing fluid to be applied to the brake caliper and...

Hi there. If you have a flex plate or a flywheel on your vehicle, the nose could be a loose bolt causing the rattling noise as the engine is running. If the noise lessens out as the engine is revved...

Hello. If the engine will not crank at all and the starter and battery are fine then I start by checking to see if the starter relay is getting power. If it is but is not sending power to the...

Hello, thank you for writing in. The vehicle is designed to start only if the vehicle is in park. This is so the vehicle will not move immediately once its started. When it comes to resolving the issue, you are...

Hi there. It really depends on the color of the smoke. If it is black then it can be a dirty air filter or a leaking fuel injector. If the smoke is white then it may have a leaking head...

You didn't say whether you got the car to run, but if you did, do not drive it. It can be very dangerous in this condition. The fuel pumped up to the engine is under pressure, so when it leaks...

Hello there, thank you for asking about your 1992 Isuzu Pickup. A professional will have the correct equipment to read OBD1 codes. Retrieving the diagnostic trouble code(s) is the first place to start when diagnosing your vehicle. Increasing RPMs changes...

Hello, thanks for writing in about your Jeep Grand Cherokee. The blower control module and connector got hot and burned from the blower motor drawing too much power. It should be replaced to fix this issue. Your A/C blower switch...

To answer this question, you will need to look up the part numbers of both to see if they match. Look up the part numbers, and then if possible, have an expert conduct a side-by-side comparison of the parts to...

Hello there, these are not uncommon problems for a vehicle to have when it sits for awhile. With the ABS light on, the most likely cause is low or poor condition brake fluid. Brake fluid absorbs moisture and can cause...

You may have an ignition system misfire due to worn spark plugs or shorting plug wires or coils. I recommend having the codes stored in computer tested to see if it points to the cause of the problem. The problem...

It is possible that you could be having an issue with your wheel bearings. I would recommend having your wheel bearings inspected by a qualified professional to determine if they are functioning properly. Oftentimes when wheel bearings have failed you...

In your particular model vehicle, the wheel bearing comes pressed into the hub assembly. It may be possible to have the old wheel bearing pressed out and have a new bearing pressed into the hub assembly, however the machine work...