Q: Getting a Check Engine code P0320.

asked by on January 12, 2016

I'm getting a Check Engine code P0320. What do I need to have done?

Check Engine Light is on Inspection $79.99 - $89.99 Get a Quote

This code signifies that the engine speed circuit for the ignition system is having a fault. I would recommend that you have this diagnosed by an experienced mechanic, like the one at YourMechanic, so they can find and correct the cause of your P0320 code.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing

What others are asking

Car cranks slowly when it is hot, but cranks normal when the engine is cold

It sounds like your starter motor could be overheating. If the starter overheats, this can cause it to malfunction. I would recommend having your starter inspected and replaced as necessary by a certified mechanic. Once you have a new starter,...

Engine starts up on cold start, shakes/struggles, and then shuts off.

Hello. I'm not sure what is meant by saying the O2 sensor and catalytic converter problem codes were not the problem. Several component issues could cause the behavior you are seeing - from a dirty, clogged, or failing idle air...

Am using Honda Accord and my TCS is always on when s on the movement of the car is very slow why

Hi there: It's common for the traction control module to develop electrical problems after it's been in use for more than 5 years. This is most likely the source of your Honda Accord's driving issues. In most cases, it's an...

The car is shaking when stopped and when you drive it hesitates and won't go to fast

There are a number of things that may cause the car to hesitate when accelerating such as low fuel pressure, a dirty or faulty mass air flow sensor, clogged or dirty fuel injectors, a faulty throttle position sensor or potentially...

OBDII fault codes

It is very possible that the intake air temperature sensor or the barometric pressure sensor will require replacement. What is likely happening is that there is a corrolation between these two sensors either because one of them is malfunctioning, there...

Tension strut replacement

Hello there, one of the commonly replaced parts on the 2009 BMW 535i is the hydraulic fluid filled bushings. These suspension components wear over time from absorbing the road shock. When the fluid filled bushings leak, it is important to...

Check Engine light P0304.

The code P0304 points to a misfire on cylinder number 4. Ford also has a funny cylinder identification pattern, different from many makes, and a diagram should be consulted to determine which cylinder is the right one. The spark plugs...

Light system Stop carefully

Hello and thank you for contacting YourMechanic. Sounds like the light control module that is located under the dash went out. Check the condition of the harness to the light control module for any corrosion or looseness. Check the fuse...

Location of oil pressure switch

The pressure switch is on the engine block, in the area of the crankshaft pulley. To replace it, disconnect the negative battery cable. Raise and safely support the vehicle. Disconnect the oil pressure sensor electrical connector. Position a drain pan...

Related articles

P2647 OBD-II Trouble Code: System Too Rich (Bank 1)
P2647 P2647 code definition A Rocker Arm Actuator System Stuck on Bank 1 What the P2647 code means This trouble code indicates that the powertrain control module has detected a malfunction in the intake camshaft rocker arm actuator system (A)....
P2400 OBD-II Trouble Code: EVAP Leak Detection Pump Control Circuit/Open
P2400 P2400 code definition EVAP Leak Detection Pump Control Circuit/Open What the P2400 code means Trouble code P2400 is set when the Engine Control Module (ECM) detects a problem on the circuit that controls the evaporative emissions (EVAP) leak detection...
P0816 OBD-II Trouble Code: Downshift Switch Circuit
P0816 means that the downshift switch circuit may have a malfunction due to faulty wiring, transmission gear, or shorted switch harness.