Q: 760866.5

asked by on December 15, 2016

I have a car that has 760866.5 miles on it and i have noticed it is starting to become very slow and struggling to move under accelerating i have took it to a garage and everything that the car needs to drive is fine no one can understand why it is doing so. What is the issue? Thank you

Car is slow to accelerate Inspection $79.99 - $89.99 Get a Quote

Hi there:

Modern cars have a very complex system that delivers fuel to the engine and rids of the vehicle of exhaust gases. A failure in any part of this system can lead to a car that is slow to accelerate. In the majority of cases, the problem can be traced back to the fuel system. However, without knowing more detailed information about your vehicle or completing a car is slow to accelerate inspection, it’ll be difficult to diagnose what’s precisely causing your issues.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing

What others are asking

Car making loud noise and won't go

Hi there, The clanking noise you have described while turning, was most likely, the axle shaft cv joint making noise. Now, given the vehicle makes metal hitting noise, won't go when put into drive or reverse, and moves when in...

Car won't start after ECM modular replacement

You did not say why the ECU was diagnosed, but the ECU would need to be programed to your specific vehicle by a dealership. If the ECU did not fix whatever issue prompted the replacement, then the car will not...

Sudden starting problem that happens sporadically

Hi there, thanks for writing in about your 1992 Oldsmobile 98. It is possible that the starter relay is failing. This relay is different than the starter solenoid that was likely replaced with the starter. The starter relay has electrical...

Brake caliper piston doesn't retract after brake pad replacement.

Hi there. If you cannot retract the caliper pistons when replacing the brake pads then you may have a master cylinder failure that is holding pressure in the braking system. If you have already replaced the pads and put everything...

Warning lights after ABS brake flex lines replaced

The ABS and brake light warning switch are on different circuits and do not work with each other. The most likely cause of the Check Brake Light message would be a wiring issue, failed bulb, improper bulb, or a brake...

Erratic RPMs, 1995 BMW 318is

Hello there, there are a few possible causes for your 1995 BMW 318is to have a fluctuation in the RPM's. The most common are a vacuum leak, oxygen sensor, throttle sensor, exhaust leak, or the fuel pump. I recommend have...

Having trouble trying to locate my knock sensor. It's throwing a code for it. 1,2,4,5,6 cylinder misfires

As you may know a knock sensor may fail for any of the following reasons: The knock sensor is faulty and needs to be replaced There is a wiring open/short/fault in the knock sensor circuit The PCM/ECM has failed...

Low coolant level light on, low oil light on

Hello. Several owners of the BMW 750i have complained of this issue. The usual fix required is a PCM reflash. The PCM flash will have to be done by BMW but it is the most likely cause and most common...

Black soot and bad smell coming from the heater vents.

Hi there. Sounds like the cabin air filter to the heating and a/c system is degrading and peeling apart. The stuff that is coming out into the cabin area is a filter full of dirt and debris. I recommend replacing...

Related articles

P0205 OBD-II Trouble Code: Injector Circuit Malfunction - Cylinder 5
P0205 P0205 code definition Injector Circuit Malfunction - Cylinder 5 What the P0205 code means P0205 is a generic diagnostic trouble code which indicates that the injector circuit for cylinder 5 has out of range voltage or resistance. This...
P0135 OBD-II Trouble Code: O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)
P0135 code definition O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1) What the P0135 code means P0135 is the OBD-II generic...
P2649 OBD-II Trouble Code: ‘A’ Rocker Arm Actuator Control Circuit High Bank 1
P2649 P2649 code definition ‘A’ Rocker Arm Actuator Control Circuit High Bank 1 What the P2649 code mean P2649 is an OBD-II code for the engine control module (ECM) detecting the ‘A’ rocker arm actuator control circuit for bank 1...