Showing articles & questions for topic
P2004

Related articles

P2004 OBD-II Trouble Code: Intake Manifold Runner Control Stuck Open Bank 1
P2004 code definition Intake Manifold Runner Control (IMRC) Stuck Open Bank 1 Related Trouble Codes: P2005: IMRC Stuck Open Bank 2 P2006:...

Related questions

Timing chain problem?

It could very well be a timing chain problem (https://www.yourmechanic.com/services/timing-chain-replacement). The P0016 and 17 indicate that the camshaft sensors (https://www.yourmechanic.com/services/camshaft-position-sensor-replacement) are sensing the camshaft in a position that does not logically correspond with the crankshaft. The P0302 (https://www.yourmechanic.com/article/p0302-obd-ii-trouble-code-cylinder-2-misfire-detected-by-jamahl-walker) and P0355...

Hi Jerel, how are you? I have a 2008 chrysler sebring convertible and my check engine light is on, I went and had it checked and s

If you are referring to Codes P2004, P2017, and related codes (https://www.yourmechanic.com/article/p2004-obd-ii-trouble-code-intake-manifold-runner-control-stuck-open-bank-1-by-jamahl-walker), if those codes have set it means that the intake manifold runner control (IMRC) is stuck or sticking. The Powertrain Control Module (PCM) provides the IMRC with information...

What does code P2004 mean?

Diagnostic trouble code P2004 (https://www.yourmechanic.com/article/p2004-obd-ii-trouble-code-intake-manifold-runner-control-stuck-open-bank-1-by-jamahl-walker) signifies a problem with a segment of the engine's air intake and control system, technically known as the intake manifold runner control (IMRC). In practical terms, the code means that the engine is not getting...

Check engine light. Code P2004 (Air Intake manifold. Runner control stuck open, bank 1.)

As you know this code is related to the intake manifold and may be caused by several potential issues such as the following: Intake Manifold Runner Binding Or Sticking (https://www.yourmechanic.com/services/intake-manifold-runner-control-replacement) Faulty Manifold flow valve Manifold flow valve harness is open...

The car shakes during braking and at stop lights, error code P0420

Hi there. The P0420 code (https://www.yourmechanic.com/article/p0420-obd-ii-trouble-code-catalyst-system-efficiency-below-threshold-bank-1-by-jamahl-walker) you are getting can cause your car to run like this. The code typically means that the catalytic converter is failing (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-catalytic-converter) or one of the oxygen sensors may be failing (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-oxygen-sensor). If it...

Windshield wipers move slow and get stuck

A few different items can cause the windshield wipers to work slow. The most common causes are the windshield motor beginning to fail (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-windshield-wiper-motor), poor electrical connection at the windshield motor, or high resistance at the wiper motor. A qualified...

Rough idling during cold starts

The vehicle will have to have the throttle body (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-throttle-body) and idle air control valve (https://www.yourmechanic.com/article/how-to-clean-an-idle-air-control-valve-by-joyce-morse) checked to see if it needs to be cleaned. Also, the engine will need to be checked for any vacuum leaks (https://www.yourmechanic.com/article/is-it-safe-to-drive-with-a-vacuum-leak) when the...

Will this service remove my check engine light and allow me to pass emissions?

The answer is "not necessarily" because the Codes you are reciting, P2004 and P2017 do NOT necessarily mean that there is anything wrong with the intake manifold runner control valve (https://www.yourmechanic.com/services/intake-manifold-runner-control-replacement) itself. The only way to determine if that valve...

code p2015 and p2004

The codes are telling you the intake manifold runners are open. They are normally closed while driving and only need to be open when the engine is off. The intake manifold depends on them being closed for proper vacuum. This...

intake control solenoid voltage

If the issue persists then it may be possible that the issue is with wiring or computer (https://www.yourmechanic.com/services/electrical-components-are-not-working-inspection). Damaged wiring or a faulty computer may compromise power to the solenoid and affect its performance. Many automotive electronic circuits use 12...

Headlights stay on after car is turned off

Hi there. If the head lights took that long to turn off then you more than likely have a failure starting in the body control module. This is a common failure on this vehicle. I typically start by reprogramming the...

Car rattles when starting, and when slowing down

When a car rattles on start up, there is a possibility that it is an engine knock (https://www.yourmechanic.com/article/what-does-it-mean-when-an-engine-knocks). An engine knock will sound like a tapping from the engine block. The more common causes of a rattle on start up...

Browse related topics

Need a mechanic?

Our certified mobile mechanics make house calls in over 700 U.S. cities. Fast, free online quotes for your car repair.

Get a quote

Post a question and get free advice from our certified mechanics.


Ask a question