The alternator on this vehicle is computer controlled and if the alternator is not communicating to the computer then it may default to a set charging rate that will show up as good when testing using standard methods. The computer...
Hi. If the door stopped working after it was shut hard, then the door lock actuator rod may have come off of the actuator or the actuator failed. It can also be due to the main switch assembly failing. Both...
Hello there, thank you for asking about your 1986 BMW 635CSi. According to the spark plug cross reference website, the A6GC is a direct replacement for the A6G. You should have no problems using that plug. If you want to...
Hello! That is an issue that many owners of your specific vehicle have faced. The issue is caused by the harness in the door being a little to short and when you open the door it literally pulls the wires...
If your engine is shutting off when it gets hot it is possible that it could be overheating. Many vehicles have a feature built into the engine that will kill the engine if it reaches a certain temperature. For an...
Those two systems are unrelated. However, there is a possibility that a wire or fuse was bumped during the transmission replacement. A special scan tool can help determine the reason for the light. An inspection of your electrical components from...
Hi there, thanks for writing in. Your particular year and model of Subaru does not need to have the valves adjusted. It uses hydraulic lifters that are self adjusting. If there is a ticking noise, it could be that...
Rough operation and loss of power on acceleration can be due to plugged fuel injectors, faulty oxygen sensors, fuel pump and/or filter, vacuum leaks, ignition system malfunctions, bad valve timing if the timing belt or chain is worn or skipped,...
Occasionally, you will be able to measure enough play in the bearing that you can condemn it without further testing. You have to check the factory spec. to see what is allowed and will have to use a dial indicator....
Is your Check Engine Light on? That may indicate that there is a diagnostic trouble code (dtc) stored. The code may help pinpoint which component requires further testing. Sometimes a dirty idle air control valve will stick during operation causing...
Hi there. From the description you have provided, the alternator may not be keeping up with additional load of the air conditioning system. This could be the result of, a loose/worn drive belt or a faulty voltage regulator which is...
Hi, thanks for writing in. There are a few things that might be going on with your ignition switch. First, the ignition cylinder might be damaged if it won't turn when you insert the key. Second, it may be the...
Hello. The cost of the repair depends on what is wrong with it. The wiring can have issues from the rear lights up to the front. A full electrical diagnostic would need to be done by a certified mechanic that...
This kind of a stalling issue can be caused by a variety of problems. They are typically caused by ignition faults, wiring faults, and fuel issues. Although you do not have a Check Engine Light on, you should still scan...
This is a generic code for the input speed sensor located on your transmission. This code may be triggered for many reasons such as a defective input speed sensor, a faulty output speed sensor, a damaged, worn, or broken reluctor...
Blower speed in your application is controlled by a replaceable resistor block in the blower motor circuit. If various fan speeds have become unusable, and now you are left with nothing, a possibility is all positions in this resistor block...
You need to have the battery and charging system checked again. You have a bad connection to battery or battery is bad and not charging. I recommend cleaning battery terminals by removing and cleaning then and reinstall then test entire...
It sounds like you have an electrical issue where the vehicle stalling may be from the charging system and battery lost connections. Your battery could be losing connection from relays clicking on and off, or the battery could be almost...
Before you can determine if the vehicle should be repaired you should have a qualified mechanic like one from YourMechanic come to you and scan the computer for you. You may have a sensor like the crankshaft sensor that could...
One of the most common causes of the brake pedal going to the floor is a loss of brake fluid. Generally, this is easy to detect due to the fact that there is usually brake fluid leaking on the ground...
Your symptoms suggest that the starter solenoid contacts are burned enough to stick in the "Start" position (engaging the starter drive and motor), even when the ignition switch is not energizing the relay portion of the starter solenoid. The starter...
Hello there, the transmission being unable to shift into reverse is a common issue for vehicles as they age and increase in mileage. There are a few common causes for this malfunction. The most likely would be low transmission fluid...
Edmunds compiles and publishes the type of data (maintenance costs) that you are seeking but for your specific year and model the entries are blank at their website, probably due to the relatively small production run of this vehicle (i.e.,...
