Dodge Nitro Car starts and then dies Inspection at your home or office.

Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.

Estimate price near me

Service Location

Customer Ratings

(185)

How A Diagnostic Works

Instantly book a certified mobile mechanic to come to you

Mechanic diagnoses the problem and quotes necessary repairs

Your vehicle is ready to go

Fair, upfront & transparent pricing for all services

Our certified mobile mechanics can come to you now.

Customer Ratings

(185)

Car starts and then dies Inspection Service

How much does a Car starts and then dies Inspection cost?

On average, the cost for a Dodge Nitro Car starts and then dies Inspection is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2008 Dodge NitroV6-4.0LService typeCar starts and then dies InspectionEstimate$114.99Shop/Dealer Price$124.99 - $132.49
2008 Dodge NitroV6-3.7LService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.01 - $112.52
2007 Dodge NitroV6-4.0LService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.01 - $112.52
2009 Dodge NitroV6-3.7LService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$104.99 - $112.48
2011 Dodge NitroV6-3.7LService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.02 - $112.55
2010 Dodge NitroV6-3.7LService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.01 - $112.52
2009 Dodge NitroV6-4.0LService typeCar starts and then dies InspectionEstimate$99.99Shop/Dealer Price$109.87 - $117.28
2010 Dodge NitroV6-4.0LService typeCar starts and then dies InspectionEstimate$99.99Shop/Dealer Price$110.24 - $117.94
Show example Dodge Nitro Car starts and then dies Inspection prices

Starting a vehicle only to have it quit immediately after can be confusing and annoying for many drivers especially if their vehicle has not experienced this type of issue before. Typically, a vehicle will start and then quit because of an issue with the fuel or electrical system. It is important to monitor fuel levels as well as warning lights which can signal to the driver that a vehicle may quit unexpectedly.

How this system works:

To start a vehicle, the electrical system, composed of the battery and starter, turns the engine over. Once running, the engine requires a constant flow of gasoline and good spark to keep that fuel igniting. If gasoline is not readily available, or if there is not enough spark, the engine will quit. More modern vehicles with sophisticated computers may affect the way the vehicle runs. These computers help the car run efficiently but can also shut a car down if the fuel/air mixture is not correct. While an older vehicle may be less sophisticated and easier to diagnose, the computers on modern cars can provide more specific information when connected to a code scanner/reader.

Common reasons for this to happen:

  • Mass Airflow Sensor: The mass airflow sensor measures how much air is entering the engine and relays this information to the vehicle’s computer so that the right amount of fuel can be delivered from the fuel injectors. When a sensor begins to fail, the vehicle’s computer may generate an error code to indicate that something has gone wrong. An issue with the mass airflow sensor may manifest itself when a car starts and then stalls soon after starting.

  • Fuel Pump Relay: The fuel pump relay functions much like a fuse for an electric fuel pump. The fuel pump relay engages as the vehicle is started and starts the fuel pump. While the vehicle is running, the fuel pump relay turns off and the fuel pump is powered by the oil pressure sending unit. If the vehicle’s computer is unable to keep the fuel pump relay running throughout the starting process, the vehicle may start and quit immediately after starting.

  • Ignition Coil: Your vehicle’s ignition coil takes the low voltage of the battery and provides the thousands of volts needed to create a spark in the spark plugs. When an ignition coil begins to fail, it may struggle to provide consistent spark to the plugs, causing the engine to stall after starting.

What to expect:

A top-rated mobile mechanic will come to your home or office to determine the reason why the vehicle starts and then dies. The mechanic will then provide a detailed inspection report outlining why the vehicle quit and the cost of any repairs that need to be made.

How it's done:

A mechanic will begin diagnosing your vehicle’s issue by plugging a code reader/scanner into the vehicle’s computer. The mechanic should be able to get more information from your vehicle’s computer on what component has failed. Using this information, the mechanic can begin necessary repairs.

If your vehicle has a bad or failing mass airflow sensor, the mechanic will begin by finding the sensor in the engine bay and checking for any signs of failure. The mechanic should check the wire harness connected to the sensor to ensure that all of wires are properly connected. After removing the sensor, the mechanic should be able to discover the nature of the failure and replace the sensor.

If the mechanic suspects an issue with the fuel pump relay, he or she should check the vehicle’s computer for a problem. If the vehicle’s computer is having difficulty providing consistent power to the fuel pump relay, the computer may need to be reprogrammed or replaced. If the vehicle’s computer is functioning normally, the mechanic may need to replace the fuel pump relay.

If the mechanic suspects that the ignition coil may be faulty, he or she should first disconnect the battery before beginning work. The mechanic should then begin the process of disconnecting wires from the ignition coil and removing it from the engine bay. The mechanic will then install the new ignition coil and ensure that it is connected properly. The mechanic should then reconnect the battery and test the new coil.

With all repairs, the mechanic will ensure the newly installed parts work properly. The mechanic can then turn off and warning lights that may have come on while the vehicle was not running properly.

How important is this service?

If your vehicle is starting but dying soon after starting, you should have it checked out by a mechanic. Issues involving the fuel management and electrical systems will become worse if not dealt with. Diligence and paying attention to warning lights may help prevent further damage to critical engine component and may save money in repairs. A vehicle that quits after starting can be inconvenient and having a mobile mechanic inspect and repair you vehicle will ensure that you and your vehicle are back on the road soon.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Dodge mechanics

Real customer reviews from Dodge owners like you.

Excellent Rating

(185)

Rating Summary
169
7
4
4
1
169
7
4
4
1

William

19 years of experience
53 reviews
William
19 years of experience
Dodge Nitro V6-3.7L - Oil Change - San Tan Valley, Arizona
William was very professional and did a great job on my car!

Charles

34 years of experience
342 reviews
Charles
34 years of experience
Dodge Nitro V6-4.0L - Window Motor / Regulator Assembly Replacement (Passenger Side Rear) - Austin, Texas
Charles did a great job. Thanks.

Peter

36 years of experience
346 reviews
Peter
36 years of experience
Dodge Nitro V6-3.7L - Car is not starting - Bonita, California
It was great, he was on time and did an amazing jog Thanks

Brandon

18 years of experience
318 reviews
Brandon
18 years of experience
Dodge Nitro V6-3.7L - Check Engine Light is on - Cary, North Carolina
Convenient service! Very knowledgeable mechanic!

Excellent Rating

(185)

Rating Summary
169
7
4
4
1
169
7
4
4
1
Number of Dodge Nitro services completed
2035+
services done by our mechanics
TOTAL NUMBER OF EXPERT Dodge MECHANICS
1400+
experts on our platform

Recent articles & questions

How Are High-Performance Ignition Systems Different from Standard Ones?
Once Once upon a time, there was only one type of ignition system. It used a distributor, points, a coil, and was subject to significant wear and tear. Then came the electronic ignition, which replaced the points with an electronic...
P2271 OBD-II Trouble Code: O2 Sensor Signal Stuck Rich Bank 1 Sensor 2
P2271 trouble code definition O2 Sensor Signal Stuck Rich Bank 1 Sensor 2 What the P2271 code means This code indicates the...
P2228 OBD-II Trouble Code: Barometric Pressure Circuit Low
P2228 code definition Barometric pressure circuit low What the P2228 code means This trouble code indicates that the powertrain control module has...

How do I activate and deactivate the ParkSense rear park assist?

There are two different ways to activate and deactivate the ParkSense rear park assist. Use the rear park assist switch in your instrument cluster. Use the electronic vehicle information center (EVIC), and follow the directions. There are three different settings...

My truck is making a chattering sound when accelerating and when shifting - 2011 Ford F-150

Hello. This is a problem of which Ford is aware, and there are several Technical Service Bulletins from Ford for this issue (#15-0114 and #11-11-6 among them). Check with your Ford service center regarding this issue, and look to these...

My doors no longer lock automatically when the car is in motion. Why is that?

The automatic door locking feature can be enabled or disabled with the master lock switch. To turn the door locking feature on, press and hold the master lock switch down for about five seconds. You will hear a beep when...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com