Audi 80 Turn Signal Switch Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(2,385)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(2,385)

Turn Signal Switch Replacement Service

How much does a Turn Signal Switch Replacement cost?

On average, the cost for a Audi 80 Turn Signal Switch Replacement is $367 with $272 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1991 Audi 80L5-2.3LService typeTurn Signal Switch ReplacementEstimate$1032.45Shop/Dealer Price$1273.69 - $1938.35
1989 Audi 80L4-2.0LService typeTurn Signal Switch ReplacementEstimate$687.43Shop/Dealer Price$849.96 - $1278.39
1992 Audi 80L5-2.3LService typeTurn Signal Switch ReplacementEstimate$1002.45Shop/Dealer Price$1243.73 - $1908.42
1990 Audi 80L4-2.0LService typeTurn Signal Switch ReplacementEstimate$1002.45Shop/Dealer Price$1243.67 - $1908.32
1988 Audi 80L4-2.0LService typeTurn Signal Switch ReplacementEstimate$639.93Shop/Dealer Price$793.72 - $1215.60
Show example Audi 80 Turn Signal Switch Replacement prices

What is the Turn Signal Switch all about?

The turn signal switch, located inside the car on the steering column, allows you to turn the signal bulbs on. Properly functioning turn signal lights are legally mandatory.

Keep in mind:

  • The wiring for brake lights usually goes through the turn signal switch. This means that if the turn signal switch has gone bad, your brake lights may not be working.
  • Some vehicles use a “combination” switch. This switch operates the turn signals, running lights, and headlights.

How it's done:

  • Inspect the switch, fuses, and wirings.
  • Remove and replace the switch if faulty.
  • Operate the turn signals verify operation of the exterior lights.

Our recommendation:

If your turn signal lights do not operate, your mechanic will visually inspect the fuse(s) and operate the switch a bit to see if he can determine where the problem is. Your mechanic should inspect all lights during every major service event.

What common symptoms indicate you may need to replace the Turn Signal Switch?

  • Left or right indicator light is not working.
  • Brake lights are not working.
  • Running lights or headlamps not working.
  • Unable to change from high to low beam and back.

How important is this service?

When you deploy the turn signal lever on your steering column, the turn signal switch is responsible for turning on your turn signals. Turn signals are a very important safety feature that alerts drivers all around you that your vehicle will soon be making a turn. When your turn signal switch dies, you have no way of turning on your turn signals. This not only makes your car less safe, but it is also illegal, and you can be given a very pricy fix-it ticket.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Audi mechanics

Real customer reviews from Audi owners like you.

Excellent Rating

(2,385)

Rating Summary
2,214
84
19
12
56
2,214
84
19
12
56

Richard

13 years of experience
601 reviews
Richard
13 years of experience
Audi TT L4-1.8L Turbo - Turn Signal Switch - Henderson, Nevada
Richard did a great job and also helped me plan out the service my car really needed, instead of what other mechanics told me. He saved me a great deal of time and money, and I truly appreciated his kindness and expertise. I have the rest of the work scheduled for next week. Thank you Richard! :)

Samuel

13 years of experience
15 reviews
Samuel
13 years of experience
Audi A4 L4-1.8L Turbo - Turn Signal Bulb Replacement (Front) - Pearland, Texas
Was 15min early which was fine. Did the job needed out in the freezing cold.

Refugio

21 years of experience
106 reviews
Refugio
21 years of experience
Audi A5 Quattro L4-2.0L Turbo - Brake Pads Replacement (Rear) - New Braunfels, Texas
Great experience working with Refugio. Efficient and very knowledgeable. I recommend this tech any day.

Mark

11 years of experience
349 reviews
Mark
11 years of experience
Audi A4 Quattro L4-2.0L Turbo - Automatic Transmission Fluid Service - Mountain View, California
Mark was going to replace the transmission fluid and fix a torn rubber cover of the drive mode selection stick. Having opened up the car he realized that he got a wrong filter part for transmission. This was not his fault (apparently yourmechanic did not ). So Mark had to come again and do a lot of extra work (for no additional pay). He also tried to glue the torn rubber. Somehow he put far too much glue and glued together parts which prevented the drive selection stick from going into some modes. He also somehow managed to leave unremovable superglue on the steering wheel. When I contacted him he came to separate the accidentally glued parts. He managed to fix the sticking but as a result also the part which was supposed to be glued disconnected again. He then told me he is going to look into replacing the part. He did not get back for two weeks. After I reminded him he said he could not figure out the part and said he'll get back to me. But after another week I just went to the authorized dealer and got it fixed. I also checked online and the part was very easy to find on audiparts.com

Excellent Rating

(2,385)

Rating Summary
2,214
84
19
12
56
2,214
84
19
12
56
Number of Audi services completed
26235+
services done by our mechanics
TOTAL NUMBER OF EXPERT Audi MECHANICS
700+
experts on our platform

Recent articles & questions

P0106 OBD-II Trouble Code: Manifold Air Pressure (MAP) Barometric Pressure Sensor Electric Circuit Output Range and Performance Problem
P0106 Trouble code definition Manifold Air Pressure (MAP) Barometric Pressure Sensor Electric Circuit Output Range and Performance Problem What the P0106 code...
P0527 OBD-II Trouble Code: Fan Speed Sensor Circuit Range or Performance Issue
P0527 means there is a range or performance issue with the fan speed sensor circuit, likely due to a faulty temperature sensor or damaged wires.
B1210 OBD-II Trouble Code: EIC Switch-2 Assembly Circuit Open
B1210 means there is an incomplete electrical circuit in the electronic instrument cluster (EIC), likely due to a circuit issue or faulty component.

When should the seat belts be replaced?

The seat belts in your car are designed to last for the life of the vehicle, but if you are involved in an accident, they’ll need to be replaced if the pretensioner was activated. Pretensioners are one-time use equipment. Once...

I have a 2005 Dodge Grand caravan. The horn does not sound when you honk, or use the key remote to lock.

Power to the horn is interrupted due to a wiring issue or the horn itself is not functioning. You can use a voltmeter to test for battery voltage at the horn terminal. If there is battery voltage, and yet the...

We just purchased a Ford e350 passenger van (2014). We drove it for a couple of hours with no problems. We then drove it through a few twisty roads in north carolina and the check [engine](/topics-engine-ford/) light came on and flashed for about a minute. It went off and we continued on to our destination which we were very close to at the time. We are concerned and don't know what to do with the vehicle since we've read that a flashing check engine light can be a real problem and we are at least 30 minutes from the nearest town and auto mechanic. Do you think we can still drive it to the nearby town or does it need to be towed there? We aren't even sure how to get a tow truck out here or if that's even possible. Thanks for your help!

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com