logo

Scion xA Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(91)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

(91)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Scion xA Brake Drum Replacement is $429 with $239 for parts and $190 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2006 Scion xAL4-1.5LService typeBrake Drum ReplacementEstimate$707.34Shop/Dealer Price$846.68 - $1219.71
2005 Scion xAL4-1.5LService typeBrake Drum ReplacementEstimate$667.34Shop/Dealer Price$806.72 - $1179.77
2004 Scion xAL4-1.5LService typeBrake Drum ReplacementEstimate$667.34Shop/Dealer Price$806.72 - $1179.76
Show example Scion xA Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Number of Scion xA services completed
1001+
services done by our mechanics
TOTAL NUMBER OF EXPERT Scion MECHANICS
500+
experts on our platform
Yourmechanic was featured in

New York Times NBC CBS Forbes INC Tech Crunch

Learn more about us

Meet some of our expert Scion mechanics

Real customer reviews from Scion owners like you.

Excellent Rating

(91)
Rating Summary
85
3
3
0
0
85
3
3
0
0

JOHNNY

31 years of experience
120 reviews
Request JOHNNY
JOHNNY
31 years of experience
Request JOHNNY
by PETER WILKENS
xA 2005 - Oxygen Sensor - Lincoln, CA
Johnny arrived right on time. He was polite and professional. The job was completed quickly and accurately.. I recommend Johnny for any of your repair needs and will be utilizing his service in the future. Thank you.

Jay

30 years of experience
1009 reviews
Request Jay
Jay
30 years of experience
Request Jay
by Susan Gogas
xA 2006 - Headlight Bulb - Sun City, CA
Painless and easy....No stress yeah!

Stacy

20 years of experience
330 reviews
Request Stacy
Stacy
20 years of experience
Request Stacy
by Destiny Hurst
xA 2005 - Service Battery/cables - Atlanta, GA
He was very detailed on what was going on with my vehicle & able to do the job in a timely fashion. Also very kind answered all my questions. Definitely recommend.

Andrew

7 years of experience
41 reviews
Request Andrew
Andrew
7 years of experience
Request Andrew
by Braniff Davis
xA 2006 - Ignition Coil - Houston, TX
Did a great job, was super fast!

Excellent Rating

(91)
Rating Summary
85
3
3
0
0
85
3
3
0
0
Number of Scion xA services completed
1001+
services done by our mechanics
TOTAL NUMBER OF EXPERT Scion MECHANICS
500+
experts on our platform
Yourmechanic was featured in

New York Times NBC CBS Forbes INC Tech Crunch

Learn more about us

Recent articles & questions

How Do I Take Care of My New Tires?
You’ve You’ve equipped your car with a brand new set of tires (https://www.goodyear.com/en-US/company/partner/yourmechanic?promoCode=YOURMECHANIC&utm_source=null&utm_medium=referral&partnerId=yourmechanic&partnerName=yourmechanic&retaggingLaunchUrl=%2F%2Fassets.adobedtm.com%2Flaunch-EN786b79de5697438cb1f8839bcd30487c.min.js&floodlightEnabled=true&liveChatEnabled=true&siteName=Goodyear+Tires), replacing the old set of worn out rubber. They were noisy, and every time you had to brake hard, you were losing traction. Now you’ve spent your...
Read more
How to Check If Your Car Has Recalls
Although Although automobile manufacturers take many precautions to ensure the safety of the vehicles they sell, defects do sometimes escape initial notice. Whether these defects arise as the result of insufficient testing of new technology or from a substandard batch...
Read more
How to Troubleshoot a Car that Nose Dives When Braking
Cars nose dive when the suspension is faulty. Inspect the car brake system, test the shocks and struts, and do a bounce test to diagnose the cause.
Read more

Can you tell me specifically what the name of this part is?

The part you indicate got damaged is called a lower control arm. You have the rear and forward lower control arms on the rear of each side of the vehicle.
Read more

I recently cleaned my battery terminals and when i connected everything back together my car just cranks and doesn't start any ide

Try to hold your throttle about 1/4 and see if it starts and then slowly return throttle to idle so computer will relearn idle again. If this does not help then you will need further diagnosis by a mechanic like...
Read more

98 Ford Expedition, the Catalyst monitor and evap monitor is on before a smog test can be done. How to get 1 of these off?

The monitors may take up to 200 miles to get them to pass since it takes special conditions to get them to pass. You can have a mechanic run the monitor test before taking to inspection stations to get checked...
Read more
  1. Home
  2. Estimates
  3. Scion
  4. xA
  5. Brake Drum Replacement

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com

Read FAQ
GET A QUOTE