Mazda 323 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mazda 323 Brake Drum Replacement is $335 with $174 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1989 Mazda 323L4-1.6L Turbo	Service typeBrake Drum Replacement	Estimate$696.18	Shop/Dealer Price$838.36 - $1226.64
1993 Mazda 323L4-1.8L	Service typeBrake Drum Replacement	Estimate$670.54	Shop/Dealer Price$805.22 - $1155.18
1992 Mazda 323L4-1.6L	Service typeBrake Drum Replacement	Estimate$537.12	Shop/Dealer Price$643.94 - $919.32
1995 Mazda 323L4-1.6L	Service typeBrake Drum Replacement	Estimate$628.88	Shop/Dealer Price$753.09 - $1071.76
1990 Mazda 323L4-1.6L	Service typeBrake Drum Replacement	Estimate$552.86	Shop/Dealer Price$663.65 - $950.86
1994 Mazda 323L4-1.6L	Service typeBrake Drum Replacement	Estimate$537.12	Shop/Dealer Price$643.94 - $919.32
1986 Mazda 323L4-1.6L	Service typeBrake Drum Replacement	Estimate$726.39	Shop/Dealer Price$864.15 - $1212.96
1987 Mazda 323L4-1.6L	Service typeBrake Drum Replacement	Estimate$726.39	Shop/Dealer Price$865.23 - $1214.85

Show example Mazda 323 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Mazda mechanics

Real customer reviews from Mazda owners like you.

Excellent Rating

(6)

Rating Summary

5

1

0

0

0

5

1

0

0

0

SEE REVIEWS NEAR ME

Kevin

33 years of experience

234 reviews

Kevin

33 years of experience

by Rebecca

Mazda 323 L4-1.6L - Starter button - Huntington Park, California

Jose

16 years of experience

324 reviews

Jose

16 years of experience

by STEVE

Mazda 323 L4-1.6L - Radiator - Hollywood, Florida

he did excellent work

Steve

37 years of experience

149 reviews

Steve

37 years of experience

by Huzefa

Mazda 323 L4-1.6L - Oil Change - Hayward, California

My car is old and easy to work on. Steve got the oil changed in minutes. Very convenient for any mechanic. I liked this service for the price to my personal wallet.

Kevin

33 years of experience

234 reviews

Kevin

33 years of experience

by Rebecca

Mazda 323 L4-1.6L - Car is not starting - Huntington Park, California

Amazing! Found the problem quickly and explained why it wasn't functioning properly. Totally transparent and super friendly. I would definitely recommend and call again.

Excellent Rating

(6)

Rating Summary

5

1

0

0

0

5

1

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

How Does My Gas Tank Know When It’s Full?

Anyone Anyone who has ever filled up a gas tank has experienced the tactile "clunk" the nozzle makes when the fuel tank is full. This sound comes from the nozzle right when the flow of fuel stops. Most people barely...

How to Buy a Good Quality Oil Cooler Hose (Automatic Transmission)

If If you’re seeing black stains beneath your vehicle when it’s parked, that oil slick could be caused by a leak in your oil cooler hose. The oil cooler acts as a radiator by cooling the engine oil after it...

How to Replace a Cruise Control Clutch Release Switch

The cruise control clutch release switch is faulty if the cruise control will not turn off or shuts off automatically while driving.

Cluck is stuck

If there is fluid coming from the slave cylinder then that needs to be replaced. A slave cylinder can fail if the clutch is worn out as it will need to work harder. I would typically start with repairing any...

Vibration at low speeds in first and second

Vibrations at low speeds or when the clutch initially engages are usually caused by hot spots on the flywheel. These hot spots are hardened areas of the flywheel that are caused by heat. When the clutch tries to engage on...

My car won't start after replacing flex pipe and Muffler

Technically, there is no connection at all between what was done on the exhaust system and the subsequent no start problem. Of course, it's always possible the Mechanic damaged something on the vehicle but such, if it occurred and if...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com