Ford Police Interceptor Sedan Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Ford Police Interceptor Sedan Brake Drum Replacement is $341 with $208 for parts and $133 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2019 Ford Police Interceptor SedanV6-3.7L	Service typeBrake Drum Replacement	Estimate$611.64	Shop/Dealer Price$732.69 - $1057.56
2018 Ford Police Interceptor SedanV6-3.5L	Service typeBrake Drum Replacement	Estimate$577.64	Shop/Dealer Price$698.72 - $1023.61
2018 Ford Police Interceptor SedanV6-3.7L	Service typeBrake Drum Replacement	Estimate$577.64	Shop/Dealer Price$698.71 - $1023.61
2013 Ford Police Interceptor SedanV6-3.7L	Service typeBrake Drum Replacement	Estimate$557.23	Shop/Dealer Price$677.28 - $1005.95
2019 Ford Police Interceptor SedanV6-3.5L	Service typeBrake Drum Replacement	Estimate$577.64	Shop/Dealer Price$698.74 - $1023.65
2014 Ford Police Interceptor SedanV6-3.7L	Service typeBrake Drum Replacement	Estimate$557.23	Shop/Dealer Price$677.31 - $1006.01
2015 Ford Police Interceptor SedanV6-3.5L	Service typeBrake Drum Replacement	Estimate$564.23	Shop/Dealer Price$684.12 - $1012.68
2017 Ford Police Interceptor SedanV6-3.7L	Service typeBrake Drum Replacement	Estimate$556.15	Shop/Dealer Price$674.54 - $997.43

Show example Ford Police Interceptor Sedan Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(4)

Rating Summary

4

0

0

0

0

4

0

0

0

0

SEE REVIEWS NEAR ME

Bryant

12 years of experience

608 reviews

Bryant

12 years of experience

by Philipp

Ford Police Interceptor Sedan V6-3.5L - Alternator - Indianapolis, Indiana

Bryan goes above and behind the call of service to ensure his clients are taken care of.

Andrew

11 years of experience

855 reviews

Andrew

11 years of experience

by Brian

Ford Police Interceptor Sedan V6-3.5L - Oil Change - Kansas City, Missouri

As always Andrew did a good job and as always the call center is HORRIBLE to deal with.

Bryant

12 years of experience

608 reviews

Bryant

12 years of experience

by Philipp

Ford Police Interceptor Sedan V6-3.5L - Car is not starting - Indianapolis, Indiana

He’s great. Hilarious guy and very friendly. Really a people person. Keep up the great work!

Colin

27 years of experience

117 reviews

Colin

27 years of experience

by ALLEN

Ford Police Interceptor Sedan V6-3.7L - Noise from engine or exhaust - Pinellas Park, Florida

Very thorough A+++

Excellent Rating

(4)

Rating Summary

4

0

0

0

0

4

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

Guide to Colored Curb Zones in Tennessee

Drivers Drivers in the state of Tennessee have to pay attention to the laws of the road while they are out and driving, but they also need to make sure they know and understand all of the parking laws present...

How to Tell the Difference Between LSD and ULSD Fuel

Low Low sulfur diesel (LSD) was replaced with ultra-low sulfur diesel (ULSD) in 2006 as part of an initiative to substantially lower the emissions of particulate matter in diesel (https://www.yourmechanic.com/article/5-essential-things-to-know-about-owning-a-diesel-car) engines. The initiative began in the European Union and later...

P0801 OBD-II Trouble Code: Reverse Inhibit Control Circuit Malfunction

P0801 means an issue with the reverse inhibitor switch making the vehicle unable to be placed in reverse or capable of doing so while driving forward.

What does the Engine Overheated -- Idle Engine message mean in a 2012 Chevrolet Equinox?

The Engine Overheated – Stop Engine message can appear on your driver information center (DIC), and is accompanied by a continuous chime. When the DIC displays this alert, the engine is too hot and can cause severe damage. Stop your...

Getting troubles codes P01217, P0300, and P0300P

It sounds like the vehicle is experiencing a few different problems that will probably need to be addressed separately. It sounds to me like there is probably an electrical short somewhere on the vehicle that is draining the battery. This...

How much do you charge for the starter replacement on 2004 honda accord 2.4

In order to replace the starter on this engine the intake manifold need to be removed. It is recommended to replace intake gaskets at the same time the starter is replaced. There has been reports of the incorrect starter is...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com