Mitsubishi Sigma Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(1,959)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(1,959)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mitsubishi Sigma Brake Drum Replacement is $701 with $540 for parts and $161 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1989 Mitsubishi SigmaV6-3.0LService typeBrake Drum ReplacementEstimate$1274.72Shop/Dealer Price$1561.54 - $2383.72
1990 Mitsubishi SigmaV6-3.0LService typeBrake Drum ReplacementEstimate$1247.40Shop/Dealer Price$1535.92 - $2363.13
Show example Mitsubishi Sigma Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mitsubishi mechanics

Real customer reviews from Mitsubishi owners like you.

Excellent Rating

(1,959)

Rating Summary
1,832
72
15
13
27
1,832
72
15
13
27

Richard

21 years of experience
461 reviews
Richard
21 years of experience
Mitsubishi Montero V6-3.5L - Air Filter - Atlanta, Georgia
Perfect!!!!! Will book nobody except Richard!!!! BOOK HIM GUYS HE IS GREAT!!!

Chris

22 years of experience
2247 reviews
Chris
22 years of experience
Mitsubishi Eclipse V6-3.0L - Oxygen Sensor Replacement (Front/Upper/Upstream, Rear/Lower/Downstream) - San Juan Capistrano, California
Chris is very personable and respectful and just got the Job Done!... Would highly recommend Chris for future car care and will certainly look for his service in the future as well. Your Mechanic is a very convenient and easy way to get your care work done, and at a very fare and straight forward pricing model. Thanks much!

Wilson

13 years of experience
296 reviews
Wilson
13 years of experience
Mitsubishi Galant L4-2.4L - Car is not starting - Orlando, Florida
He was timely, and kind answered all my questions.

Wesley

16 years of experience
277 reviews
Wesley
16 years of experience
Mitsubishi Galant L4-2.4L - Steering wheel does not turn car - Louisville, Colorado
Wesley is sharp , intelligent. fixed my car in just some minutes. Thanks a ton :)

Excellent Rating

(1,959)

Rating Summary
1,832
72
15
13
27
1,832
72
15
13
27
Number of Mitsubishi services completed
21549+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mitsubishi MECHANICS
700+
experts on our platform

Recent articles & questions

How to Calculate the Value of a Salvaged Car
An unfortunate part of driving is the possibility of a collision that’s severe enough to write off your car as a total loss. While the most important concern in any collision is the safety of all the involved parties, you’re...
Indiana Parking Laws: Understanding the Basics
When When driving on the roads of Indiana, abiding by the laws and regulations of the road is par for the course. However, drivers also need to make sure they abide by the laws when they are finding places to...
How To Jumpstart Your Car
A how-to guide to jumpstart your vehicle in the event of a dead battery. You'll need jumper cables, safety glasses, and a properly starting car.

Headlights go out randomly, will come back on after

As silly as it sounds, the issue is most likely caused by an intermittent failure in your Totally Integrated Power Module (TIPM). Of course it’s important to have the circuit and connections checked, but the TIPM is the most common...

Right turn produces noise - 2011 Toyota Camry

Hi there. It sounds like you have a wheel bearing (https://www.yourmechanic.com/services/wheel-bearings-replacement) or axle failure (https://www.yourmechanic.com/services/axle-cv-shaft-assembly-replacement). A failing wheel bearing will generally produce more noise when loaded; LF when turning right and RF when turning left. An axle can produce similar...

I have a 97bmw528i And i fixed my air intake boot on it and drove fine for that day next day the car would barely move the more I

Code P0730 (https://www.yourmechanic.com/article/p0730-obd-ii-trouble-code-incorrect-gear-ratio-by-ian-swan) is linked to the problem you are describing. Therefore, it's worth ruling in or out the typical causes of code P0730 which include dirty transmission fluid, low fluid, blocked filter, broken mechanical components within transmission, internal blockage...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com