Mercedes-Benz C32 AMG Noise from engine or exhaust Inspection at your home or office.

Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.

Estimate price near me

Service Location

Customer Ratings

(5)

How A Diagnostic Works

Instantly book a certified mobile mechanic to come to you

Mechanic diagnoses the problem and quotes necessary repairs

Your vehicle is ready to go

Fair, upfront & transparent pricing for all services

Our certified mobile mechanics can come to you now.

Customer Ratings

(5)

Noise from engine or exhaust Inspection Service

How much does a Noise from engine or exhaust Inspection cost?

On average, the cost for a Mercedes-Benz C32 AMG Noise from engine or exhaust Inspection is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2002 Mercedes-Benz C32 AMGV6-3.2L TurboService typeNoise from engine or exhaust InspectionEstimate$114.99Shop/Dealer Price$139.99 - $158.75
2003 Mercedes-Benz C32 AMGV6-3.2L TurboService typeNoise from engine or exhaust InspectionEstimate$94.99Shop/Dealer Price$120.04 - $138.82
2004 Mercedes-Benz C32 AMGV6-3.2L TurboService typeNoise from engine or exhaust InspectionEstimate$94.99Shop/Dealer Price$120.03 - $138.82
Show example Mercedes-Benz C32 AMG Noise from engine or exhaust Inspection prices

Your car’s engine makes quite a racket. Some sounds are music to the ears like the exhaust note of a finely tuned V12. (Some manufacturers have resorted to placing speakers under the dash to simulate the sound.) On the other hand, some are cries for help, such as the jolt of a backfire, the snake-like hiss of a ruptured hose, or the incessant tapping of a defective lifter.

Common reasons for this to happen:

Here’s a guide to engine noises and some potential causes.

Whirring

Description: A vibrating or buzzing, much like the sound a window fan makes when turned on.

Cause: A whirring sound that changes in relation to engine speed could indicate trouble brewing under the hood. There are a myriad of possible causes, typically on belt driven accessories or the belt(s) themselves. Your mechanic will start by listening to the bearings of your alternator, idler, and tensioner pulleys. If no problem is found, the water pump is a likely culprit.

Hissing, Gurgling, and/or Sizzling

Description: Hissing sounds like air or steam escaping from a pipe or hose. Sizzling is like a slice of bacon in a hot griddle.

Cause: These three sounds often go hand-in-hand with an overheating engine. The hissing means your cooling system has possibly developed a leak. Gurgling sounds like a coffee pot percolating, and is the result of coolant boiling (which is abnormal in a properly operating system). Sizzling is the result of that coolant or oil landing on a heated engine component like, say, the exhaust manifold. The best course of action is to pull over as soon as safely possible, let the engine cool down and call a mechanic. If the car isn’t overheating but is still hissing, other possible maladies include a clogged exhaust and catalytic converter, but these are usually associated with more noticeable problems driving.

Loud Exhaust Note

Description: We are not talking about a throaty, grumbling, wonderfully musical exhaust note. No. We are talking about loud noises that occur unintentionally and suddenly.

Cause: The most likely perpetrator here will be a broken muffler or exhaust pipe. If a loss in performance accompanies that noise, then the problem is likely something deeper, possibly a cracked exhaust manifold or broken catalytic converter.

Backfires

Description: A blast from an M-80. Technically, a backfire is fuel detonating outside the combustion chamber. It can occur in either the intake system or the exhaust system, depending on the cause.

Cause: The most common is moisture or water in the fuel system. While your car’s gas tank may be tightly sealed, H2O can still seep in as the result of condensation caused by changes in humidity and/or dramatic swings in outside temperatures. The fuel filter should remove it, but some water can get by, especially if the filter is old. An unbalanced air-to-fuel mixture is the suspect of interest here, and may be from leaky vacuum hoses or a malfunctioning air intake valve.

Sputtering

Description: Imagine a jerking action from the engine and/or powertrain. The engine indiscriminately loses power, or rpms fluctuate, as the driver accelerates.

Cause: An incomplete combustion event. While this doesn’t sound dire, it can cause serious damage to other engine components, specifically catalytic converters. On 1996 and later models, a misfire will typically be accompanied by a flashing check engine light.. Have the technician check the ignition system, not just simply replace the spark plugs. This includes examining the ignition coil, rotor, cap, and wires (if so equipped).

A blocked or malfunctioning fuel injector will also cause your car to sputter. In some cases, it may be accompanied by a steady clicking sound.

Tapping or Clicking

Description: Imagine the sound made by a watch's movement or a ratcheting wrench. It’s a metallic tick, as though someone is striking the inside of the engine block with a metal stick in a rhythmic manner.

Cause: When tapping is engine related, it is usually more pronounced at idle, and increases in speed with engine RPM.. It may disappear at high speeds. In this case, it is probably upper valve train or tappet noise caused by either low oil pressure, excessive valve clearance or a defective hydraulic valve lifter.

The most common cause -- and easiest to remedy -- is that the engine is low on oil. Another answer is that there is some blockage in the system. Culprits could include a worn or damaged oil pump or a clogged oil filter. If you haven't had your oil and filter changed in a while, consider doing so immediately.

If it's not an oil issue, it's potentially related to the valve train, as we stated above; i.e., a serious internal engine problem that is preventing normal oil pressure from reaching the upper valve train components.

Spark Knocking (Preignition)

Description: A light, metallic knocking sound, usually under acceleration.

Cause: Knocking is most commonly attributed to improper ignition timing, lean air/fuel ratio, overheating, or improper fuel octane level.

It's a common misconception that there are benefits to using a higher-octane gasoline in your vehicle than the owner's manual specifies; however, using a lower-grade fuel can very well produce engine knock.

Bearing Knock

Description: Bearing knock is typically a deeper tone, directly related to engine RPM.

Cause: It is typically associated with excessive main bearing clearance (a regular, rumble-like knock), worn connecting rod bearings (sharp, irregular knock).Bearing knocks usually involve labor-intensive repairs. The good news is, regularly performed preventative maintenance (oil and filter changes) will typically prevent bearing damage from occurring for the life of your vehicle.

What to expect:

A top-rated mobile mechanic will come to your home or office to determine the source and cause of the engine or exhaust noise, and will then provide a detailed inspection report that includes the scope and cost of the necessary repairs.

How it's done:

The mechanic will typically begin by listening to identify the general source of the noise. In the case of potential belt or accessory noise, a stethoscope is used while the engine is running to listen to individual bearings under load. A noise that has a corresponding drivability concern (misfire, preignition), will usually be approached with a scanner or code reader, to determine which electrical system may be malfunctioning. Internal engine noises (knock, tick) will almost always begin by checking the engine oil level. If the oil level and condition are acceptable, a more extensive disassembly may be required.

How important is this service?

Given that a noise can indicate a minor or major issue, it's wise to book a mechanic to perform an inspection as soon as possible and learn promptly what's at the root of the engine or exhaust noise.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0

Chris

22 years of experience
2229 reviews
Chris
22 years of experience
Mercedes-Benz C32 AMG V6-3.2L Turbo - Fuel Filter Replacement - Winchester, California
Chris arrived and replaced the fuel filter flawlessly.

Joe

15 years of experience
453 reviews
Joe
15 years of experience
Mercedes-Benz C32 AMG V6-3.2L Turbo - Car is making a noise - Nashville, Tennessee
Joe is very friendly and professional, went above and beyond to address my car service needs.

James

31 years of experience
690 reviews
James
31 years of experience
Mercedes-Benz C32 AMG V6-3.2L Turbo - Car is not starting - Cypress, California
He came prepared and came early. Did a lot of tests and discovered that I needed a fuel pump along with some other repairs.

Alexis

30 years of experience
94 reviews
Alexis
30 years of experience
Mercedes-Benz C32 AMG V6-3.2L Turbo - Pre-purchase Car Inspection - Miami, Florida
Alexis was great, very helpful answered all of my questions.

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0
Number of Mercedes-Benz C32 AMG services completed
55+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

Symptoms of a Bad or Failing Fuel Meter Assembly
Common signs include the fuel gauge behaving erratically and getting stuck on full or empty.
How to Get a New Hampshire Driver's Permit
New New Hampshire is one of the few states that does not use a graduated driver’s license program. The DMV in the state does not issue learner’s permits. The state of New Hampshire allows anyone over the age of 15...
P0339 OBD-II Trouble Code: Crankshaft Position Sensor A Circuit Intermittent
P0339 means that the car's computer has detected a voltage signal from the crankshaft position sensor that exceeds maximum specifications.

Does a transmission module needs to be reset after replacing the transmission?

Hello there, in some cases the transmission control module will need to be reflashed or programmed to the new transmission or it will need to be updated with the newest software. Usually, only dealers have the ability to program the...

Bushings are worn out, do I need to change the sway bar as well? Pls help

Generally, replacing the bushings should keep the sway bar operating properly and doing what it is designed to do. When replacing the bushings, you may want to inspect the sway bar to make sure it is not bent or damaged...

Good day so i replaced a [timing belt](/topics-timing-belt/) on a 2002 hyundai santa fe and was given some bad advice on top dead center and i need some clarification on how to resolve So i have set the engine now at top deac center on the compression stroke the problem before it was set on the exhaust stroke. Now that i did that the crank pulley lines up fine, piston is at top dead center on compression stroke howevr both cams timing marks are off 180 degrees. note this is on a 2.7 v6 Now what i am wondering is can i just take the belt off rotate the top two cams to the right (front of the car) till they align with timing marks and put it all back together and everything be ok.

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com