Jeep Scrambler Valve Cover Gasket Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(6)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(6)

Valve Cover Gasket Replacement Service

How much does a Valve Cover Gasket Replacement cost?

On average, the cost for a Jeep Scrambler Valve Cover Gasket Replacement is $169 with $36 for parts and $133 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1981 Jeep ScramblerL6-4.2LService typeValve Cover Gasket ReplacementEstimate$619.88Shop/Dealer Price$735.48 - $1035.03
1982 Jeep ScramblerL4-2.5LService typeValve Cover Gasket ReplacementEstimate$278.35Shop/Dealer Price$328.71 - $448.25
1982 Jeep ScramblerL6-4.2LService typeValve Cover Gasket ReplacementEstimate$577.88Shop/Dealer Price$693.52 - $993.09
1983 Jeep ScramblerL4-2.5LService typeValve Cover Gasket ReplacementEstimate$278.35Shop/Dealer Price$328.68 - $448.19
1984 Jeep ScramblerL4-2.5LService typeValve Cover Gasket ReplacementEstimate$278.35Shop/Dealer Price$328.73 - $448.29
1981 Jeep ScramblerL4-2.5LService typeValve Cover Gasket ReplacementEstimate$278.35Shop/Dealer Price$328.71 - $448.25
1983 Jeep ScramblerL6-4.2LService typeValve Cover Gasket ReplacementEstimate$588.38Shop/Dealer Price$703.73 - $1003.09
1985 Jeep ScramblerL4-2.5LService typeValve Cover Gasket ReplacementEstimate$221.91Shop/Dealer Price$255.27 - $320.74
Show example Jeep Scrambler Valve Cover Gasket Replacement prices

What is a valve cover gasket and how does it work?

Each cylinder head on your car’s engine has an aluminum or plastic valve cover bolted to it. Between this valve cover and the cylinder head, there is a gasket that keeps engine oil from leaking out. The valve cover bolts keep the gasket compressed, thus preventing leaks. Over time the gasket becomes brittle from the engine’s heat or the bolts loosen, creating an engine oil leak.

When to consider replacing a valve cover gasket?

Look for these signs of oil leakage at the valve cover gasket:

  • Oil seepage or dripping. Should the joint between the valve cover and the cylinder head fail, oil often becomes visible on the valve cover or cylinder heads. Usually, the oil will attract and hold dirt.
  • Oil accumulating inside the spark plug well. The spark plug tube seals are part of the valve cover sealing system. If the tube seals are leaking, you will see oil on the spark plugs or wires. The valve cover gasket and tube seals are all replaced at one time if either fails.
  • Oil leakage at the rubber grommets. The bolts holding the valve cover to the cylinder head sometimes have rubber grommet seals under the bolt heads. If these seals are leaking, you will see oil seepage around the bolt heads.

How do mechanics replace a valve cover gasket?

  • Remove engine cover. Some engines have plastic covers over the entire top. The plastic engine cover is removed to access the valve cover(s).
  • Remove components. On 4 cylinder engines, the valve cover is usually readily accessed once any electrical components and emission control tubing are removed, plus any accelerator linkages that might be in the way. On 6 or 8 cylinder engines, depending on which valve cover gasket is leaking, removal of the air intake plenum might be required, as well as additional steps.
  • Remove valve cover. Once the valve cover(s) is accessed, the cover retaining bolts are removed and the cover pulled off. The valve cover sealing surface is checked with a straight edge to be sure the cover is flat and thus reusable.
  • Install new gasket. The new valve cover gasket is applied along with new rubber grommets under the retaining bolt heads. If there are spark plug tube seals, these are replaced as well. In some applications, oil resistant RTV (room temperature vulcanization) sealant must be applied to specific segments of the sealing surface, along with the new gasket, to ensure a complete and effective seal. The cover is bolted back on, using a calibrated inch pound torque wrench, and all other components are restored to their original position.
  • Check for leaks. Finally, the car engine is run and a visual check is made for oil leaks.

Is it safe to drive with a valve cover gasket problem?

Yes, as long as the amount of oil leaking is small, and there is no leak onto hot engine parts such as the exhaust manifold, it is safe to drive your car until you have an opportunity to fix it.

If you notice oil leaking on to the ground beneath your car after it is parked, you do not have a small leak, and it needs to be found and repaired as soon as possible. Any leak, of course, means your oil level is dropping as you drive the car. If you have a leak, be sure to check your oil more frequently than usual so you do not run low on oil and damage the engine.

When replacing a valve cover gasket keep in mind:

  • The mechanical components of a car engine will typically outlive the gaskets used to seal the engine. However, many of these gaskets, including the valve cover gaskets, are relatively easy to replace.
  • Never add stop leak type products to engine oil or other vehicle fluids. Not only are these materials not approved or specified by the original equipment manufacturers, but they also can create additional problems that may be costly to repair.
  • Often, if a car is old enough to have a valve cover oil leak, there will be oil leaks elsewhere on the engine, so you should request a complete leak inspection. It may be more cost effective to repair multiple leaks during one service call.
  • Often, the PCV (Positive Crankcase Ventilation) valve is inserted into a rubber grommet in one of the valve covers. An old rubber grommet is a potential leak source, as well as connections to the PCV valve. These components should be inspected and considered for replacement while there is access to the valve cover.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Jeep mechanics

Real customer reviews from Jeep owners like you.

Excellent Rating

(6)

Rating Summary
5
1
0
0
0
5
1
0
0
0

Cesar

9 years of experience
292 reviews
Cesar
9 years of experience
Jeep Scrambler L4-2.5L - Ignition Switch - Edmonds, Washington
Great job!

Abdul

11 years of experience
419 reviews
Abdul
11 years of experience
Jeep Scrambler L6-4.2L - Water Pump - Atlanta, Georgia
Excellent

Jacob

12 years of experience
329 reviews
Jacob
12 years of experience
Jeep Scrambler L6-4.2L - Transfer Case Output Shaft Seal Replacement (Front) - Dallas, Texas
Jacob did a great job and was very thorough. Great attention to detail and left my garage cleaner than he found it. I've already booked another service with him.

Joseph

20 years of experience
640 reviews
Joseph
20 years of experience
Jeep Scrambler L6-4.2L - Car is not starting - South Jordan, Utah
Arrived on time but was unable to diagnose because I had an older vehicle. He was able to suggest possible fixes and put me in contact with my aftermarket fuel injection kit providers for possible help. Was extremely knowledgeable and upfront. Would recommend for newer vehicles.

Excellent Rating

(6)

Rating Summary
5
1
0
0
0
5
1
0
0
0
Number of Jeep Scrambler services completed
66+
services done by our mechanics
TOTAL NUMBER OF EXPERT Jeep MECHANICS
1300+
experts on our platform

Recent articles & questions

5 Essential Things to Know About Car Loans
Unless Unless you’re sitting on plenty of cash, you’ll likely need to finance your new car. There are plenty of options available for car loans, and that can make things tricky – especially if you’re trying to decide between new...
Symptoms of a Bad or Failing Control Arm Assembly
Common signs include a vibrating steering wheel, steering pulling to the left or right, and clunking noises.
P0184 OBD-II Trouble Code: Fuel Temperature Sensor "A" Circuit Intermittent
P0184 P0184 trouble code definition Fuel Temperature Sensor "A" Circuit Intermittent What the P0184 code means P0184 is a generic OBD-II code indicating that the fuel temperature sensor A is intermittent; either the sensor input is not steady and goes...

Automatic transmission jerking

Hello. A common cause of transmission hard shifting is dirty transmission fluid. I suggest checking the transmission fluid (https://www.yourmechanic.com/services/transmission-fluid-service). However, it is quite likely that the cause of the transmission malfunction is that the transmission module needs reprogramming. There is...

What are the toque specs for a inner tie rod for a 2003 Ford ranger 2wd?

Hello. The torque specification for the inner tie rod on this vehicle is 74 foot pounds. Make sure that you properly lock the tie rod down also.

Charging system warning light.

You may have a failing voltage regulator that could be allowing the alternator to supply too much or too little amperage to the battery resulting in the battery never maintaining a consistent charge as it is designed to. The voltage...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com