Jeep J20 Valve Cover Gasket Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Valve Cover Gasket Replacement Service

How much does a Valve Cover Gasket Replacement cost?

On average, the cost for a Jeep J20 Valve Cover Gasket Replacement is $171 with $38 for parts and $133 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1975 Jeep J20V8-5.9L	Service typeValve Cover Gasket Replacement	Estimate$521.67	Shop/Dealer Price$625.84 - $906.85
1979 Jeep J20V8-5.9L	Service typeValve Cover Gasket Replacement	Estimate$493.67	Shop/Dealer Price$597.86 - $878.89
1977 Jeep J20V8-6.6L	Service typeValve Cover Gasket Replacement	Estimate$403.75	Shop/Dealer Price$485.46 - $699.05
1980 Jeep J20V8-5.9L	Service typeValve Cover Gasket Replacement	Estimate$493.67	Shop/Dealer Price$597.83 - $878.83
1977 Jeep J20V8-5.9L	Service typeValve Cover Gasket Replacement	Estimate$493.67	Shop/Dealer Price$597.88 - $878.93
1981 Jeep J20V8-5.9L	Service typeValve Cover Gasket Replacement	Estimate$493.67	Shop/Dealer Price$597.86 - $878.89
1982 Jeep J20V8-5.9L	Service typeValve Cover Gasket Replacement	Estimate$500.67	Shop/Dealer Price$604.67 - $885.56
1986 Jeep J20V8-5.9L	Service typeValve Cover Gasket Replacement	Estimate$216.19	Shop/Dealer Price$249.59 - $317.51

Show example Jeep J20 Valve Cover Gasket Replacement prices

What is a valve cover gasket and how does it work?

Each cylinder head on your car’s engine has an aluminum or plastic valve cover bolted to it. Between this valve cover and the cylinder head, there is a gasket that keeps engine oil from leaking out. The valve cover bolts keep the gasket compressed, thus preventing leaks. Over time the gasket becomes brittle from the engine’s heat or the bolts loosen, creating an engine oil leak.

When to consider replacing a valve cover gasket?

Look for these signs of oil leakage at the valve cover gasket:

Oil seepage or dripping. Should the joint between the valve cover and the cylinder head fail, oil often becomes visible on the valve cover or cylinder heads. Usually, the oil will attract and hold dirt.
Oil accumulating inside the spark plug well. The spark plug tube seals are part of the valve cover sealing system. If the tube seals are leaking, you will see oil on the spark plugs or wires. The valve cover gasket and tube seals are all replaced at one time if either fails.
Oil leakage at the rubber grommets. The bolts holding the valve cover to the cylinder head sometimes have rubber grommet seals under the bolt heads. If these seals are leaking, you will see oil seepage around the bolt heads.

How do mechanics replace a valve cover gasket?

Remove engine cover. Some engines have plastic covers over the entire top. The plastic engine cover is removed to access the valve cover(s).
Remove components. On 4 cylinder engines, the valve cover is usually readily accessed once any electrical components and emission control tubing are removed, plus any accelerator linkages that might be in the way. On 6 or 8 cylinder engines, depending on which valve cover gasket is leaking, removal of the air intake plenum might be required, as well as additional steps.
Remove valve cover. Once the valve cover(s) is accessed, the cover retaining bolts are removed and the cover pulled off. The valve cover sealing surface is checked with a straight edge to be sure the cover is flat and thus reusable.
Install new gasket. The new valve cover gasket is applied along with new rubber grommets under the retaining bolt heads. If there are spark plug tube seals, these are replaced as well. In some applications, oil resistant RTV (room temperature vulcanization) sealant must be applied to specific segments of the sealing surface, along with the new gasket, to ensure a complete and effective seal. The cover is bolted back on, using a calibrated inch pound torque wrench, and all other components are restored to their original position.
Check for leaks. Finally, the car engine is run and a visual check is made for oil leaks.

Is it safe to drive with a valve cover gasket problem?

Yes, as long as the amount of oil leaking is small, and there is no leak onto hot engine parts such as the exhaust manifold, it is safe to drive your car until you have an opportunity to fix it.

If you notice oil leaking on to the ground beneath your car after it is parked, you do not have a small leak, and it needs to be found and repaired as soon as possible. Any leak, of course, means your oil level is dropping as you drive the car. If you have a leak, be sure to check your oil more frequently than usual so you do not run low on oil and damage the engine.

When replacing a valve cover gasket keep in mind:

The mechanical components of a car engine will typically outlive the gaskets used to seal the engine. However, many of these gaskets, including the valve cover gaskets, are relatively easy to replace.
Never add stop leak type products to engine oil or other vehicle fluids. Not only are these materials not approved or specified by the original equipment manufacturers, but they also can create additional problems that may be costly to repair.
Often, if a car is old enough to have a valve cover oil leak, there will be oil leaks elsewhere on the engine, so you should request a complete leak inspection. It may be more cost effective to repair multiple leaks during one service call.
Often, the PCV (Positive Crankcase Ventilation) valve is inserted into a rubber grommet in one of the valve covers. An old rubber grommet is a potential leak source, as well as connections to the PCV valve. These components should be inspected and considered for replacement while there is access to the valve cover.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Jeep mechanics

Real customer reviews from Jeep owners like you.

Excellent Rating

(116)

Rating Summary

108

6

1

1

0

108

6

1

1

0

SEE REVIEWS NEAR ME

Luis

12 years of experience

78 reviews

Luis

12 years of experience

by Dirk

Jeep J20 V8-6.6L - Car is not starting - Los Lunas, New Mexico

great

Chris

22 years of experience

2223 reviews

Chris

22 years of experience

by Brett

Jeep Cherokee L6-4.0L - Valve Cover Gasket - Lake Forest, California

Chris is great as always

James

30 years of experience

873 reviews

James

30 years of experience

by Michael

Jeep Wrangler L4-2.5L - Valve Cover Gasket Replacement - Orlando, Florida

James went above and beyond today replacing the valve cover gasket and performing an oil change on my '95 Wrangler. He arrived right on time and got right to work. He is always friendly and respectful. I will continue to request James whenever I use YourMechanic.

Roberto

12 years of experience

304 reviews

Request Roberto

Roberto

12 years of experience

Request Roberto

by Fabeola

Jeep Grand Cherokee L6-4.0L - Valve Cover Gasket - Houston, Texas

Roberto arrived early and finished early. He answered all my questions and made sure what I had done and what follow up I would need in the future. He was very polite, I would recommend him to anyone looking for a mechanic.

Excellent Rating

(116)

Rating Summary

108

6

1

1

0

108

6

1

1

0

SEE REVIEWS NEAR ME

Recent articles & questions

A Buyer’s Guide to the 2013 Subaru BRZ

This This sports car for the everyday man or woman is an irresistible combination of style, handling, and just plain fun. The BRZ offers a respectably good time on the way to work or on the way around the race...

Symptoms of Bad or Failing Air Shocks

If your car is riding less comfortably, nose dives when braking, or leans when turning, you may need to replace your air shocks.

P2501 OBD-II Trouble Code: Generator Lamp/L-Terminal Circuit High

P2501 means there is an issue with the generator lamp control circuit. This could be due to defects in the alternator, battery, or starter.

Engine is knocking loudly and has a weak acceleration.

You may have damaged the engine bearings by running it low on oil. I would suggest not driving it until you have an engine mechanic listen to and diagnose where the noise is coming from. If the noise is up...

Fuel Pump not coming on

You say you are getting battery power and ground to the fuel pump but the pump is not coming on? If this is the case, then the pump connector is bad. There is a technical bulletin (http://www.airtexproducts.com/Resources/TSB/TSB-1010-01_ATX.pdf) that the connector...

Car loses power while driving 2001 Ford Focus

Hi there: This issue is commonly caused by three different systems, ignition system, fuel system and the emissions system components including O2 sensors and the EGR Valve. The best way to know for certain and before you spend any money...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com