Dodge Intrepid Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Dodge Intrepid Brake Drum Replacement is $266 with $171 for parts and $95 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1994 Dodge IntrepidV6-3.5L	Service typeBrake Drum Replacement	Estimate$571.34	Shop/Dealer Price$676.68 - $947.71
1993 Dodge IntrepidV6-3.3L	Service typeBrake Drum Replacement	Estimate$531.34	Shop/Dealer Price$636.72 - $907.77
1997 Dodge IntrepidV6-3.3L	Service typeBrake Drum Replacement	Estimate$531.34	Shop/Dealer Price$636.72 - $907.76
1997 Dodge IntrepidV6-3.5L	Service typeBrake Drum Replacement	Estimate$531.34	Shop/Dealer Price$636.67 - $907.68
2000 Dodge IntrepidV6-3.5L	Service typeBrake Drum Replacement	Estimate$519.23	Shop/Dealer Price$635.32 - $961.03
2003 Dodge IntrepidV6-2.7L	Service typeBrake Drum Replacement	Estimate$519.23	Shop/Dealer Price$635.31 - $961.00
2000 Dodge IntrepidV6-2.7L	Service typeBrake Drum Replacement	Estimate$524.23	Shop/Dealer Price$640.17 - $965.76
2004 Dodge IntrepidV6-2.7L	Service typeBrake Drum Replacement	Estimate$524.23	Shop/Dealer Price$640.54 - $966.42

Show example Dodge Intrepid Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Dodge mechanics

Real customer reviews from Dodge owners like you.

Excellent Rating

(85)

Rating Summary

76

2

3

0

4

76

2

3

0

4

SEE REVIEWS NEAR ME

Joseph

24 years of experience

44 reviews

Joseph

24 years of experience

by Parijat

Dodge Intrepid V6-3.5L - Thermostat - New River, Arizona

Highly efficient and professional mechanic. He is knowledgeable and pays good attention to detail. He did an overall great job and also kept the work area clean. I would highly recommend Joseph Jock.

David

25 years of experience

9 reviews

David

25 years of experience

by Treazure

Dodge Intrepid V6-3.5L - Check Engine Light is on - Tallahassee, Florida

He showed up on time. He did a thorough diagnosis & quickly resolved my issue. He was great!

Chris

20 years of experience

448 reviews

Chris

20 years of experience

by Daisy

Dodge Intrepid V6-3.3L - Car Battery Replacement - Portland, Oregon

Chris is professional and straight to business. Unlike my past experiences with different mechanics, I appreciate the fact that there wasn't any pressure to purchase any unnecessary services.

Wesley

16 years of experience

277 reviews

Wesley

16 years of experience

by Sadaya

Dodge Intrepid V6-3.2L - Battery - Denver, Colorado

Wesley s. Come the same day a requested for a mechanic and he even come about an hour early. I was really impressed with how good he is at what he does even though I had to make another appointment to get the car running witch was not his falt. He told me everythng he was going to do to my car and did everythng right in front of me. He also took his time to smoke sure he did everythng he could to fix my car and put back together the pieces the other mechanic took a part. Thank you Wesley.

Excellent Rating

(85)

Rating Summary

76

2

3

0

4

76

2

3

0

4

SEE REVIEWS NEAR ME

Recent articles & questions

How Do I Prepare My Car for Winter?

Your Your car needs special care and attention during the cold months. To keep it running smoothly, follow these steps: Change your oil and oil filter regularly: Make sure you follow the recommendations as specified in your manual. You might...

Insurance Requirements for Car Registration in Wyoming

The The Wyoming Department of Transportation requires that all drivers carry minimum amounts of liability insurance, or “financial responsibility” in order to legally operate a vehicle on the Wyoming roadways. Most drivers choose to purchase insurance through a provider, but...

How to Get Smog Technician Certified in North Carolina

Automotive technician jobs include smog certified emissions inspectors. In North Carolina, you need to work at a licensed inspection station.

Car sputters when accelerating. Not the spark plugs checked those. Now where do I go from here

Ignition coils will fail and cause a sputtering or a misfire, but there could be other issues as well. Since the car is a 96, you might be able to retrieve trouble codes that will tell you which cylinders are...

Starter

If striking the starter motor case with a rubber mallet brings the starter to life, that typically means there is a bad spot on the starter motor armature. The vibration from striking the motor simply moves the armature just enough...

M2013 300 c mercedes 300 c sorry 2013

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com