Chevrolet Bolt EV Car starts and then dies Inspection at your home or office.

Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.

Estimate price near me

Service Location

Customer Ratings

(5)

How A Diagnostic Works

Instantly book a certified mobile mechanic to come to you

Mechanic diagnoses the problem and quotes necessary repairs

Your vehicle is ready to go

Fair, upfront & transparent pricing for all services

Our certified mobile mechanics can come to you now.

Customer Ratings

(5)

Car starts and then dies Inspection Service

How much does a Car starts and then dies Inspection cost?

On average, the cost for a Chevrolet Bolt EV Car starts and then dies Inspection is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2019 Chevrolet Bolt EVElectricService typeCar starts and then dies InspectionEstimate$114.99Shop/Dealer Price$124.99 - $132.49
2021 Chevrolet Bolt EVElectricService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.01 - $112.52
2020 Chevrolet Bolt EVElectricService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.01 - $112.52
2017 Chevrolet Bolt EVElectricService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$104.99 - $112.48
2018 Chevrolet Bolt EVElectricService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.02 - $112.55
2022 Chevrolet Bolt EVElectricService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.01 - $112.52
Show example Chevrolet Bolt EV Car starts and then dies Inspection prices

Starting a vehicle only to have it quit immediately after can be confusing and annoying for many drivers especially if their vehicle has not experienced this type of issue before. Typically, a vehicle will start and then quit because of an issue with the fuel or electrical system. It is important to monitor fuel levels as well as warning lights which can signal to the driver that a vehicle may quit unexpectedly.

How this system works:

To start a vehicle, the electrical system, composed of the battery and starter, turns the engine over. Once running, the engine requires a constant flow of gasoline and good spark to keep that fuel igniting. If gasoline is not readily available, or if there is not enough spark, the engine will quit. More modern vehicles with sophisticated computers may affect the way the vehicle runs. These computers help the car run efficiently but can also shut a car down if the fuel/air mixture is not correct. While an older vehicle may be less sophisticated and easier to diagnose, the computers on modern cars can provide more specific information when connected to a code scanner/reader.

Common reasons for this to happen:

  • Mass Airflow Sensor: The mass airflow sensor measures how much air is entering the engine and relays this information to the vehicle’s computer so that the right amount of fuel can be delivered from the fuel injectors. When a sensor begins to fail, the vehicle’s computer may generate an error code to indicate that something has gone wrong. An issue with the mass airflow sensor may manifest itself when a car starts and then stalls soon after starting.

  • Fuel Pump Relay: The fuel pump relay functions much like a fuse for an electric fuel pump. The fuel pump relay engages as the vehicle is started and starts the fuel pump. While the vehicle is running, the fuel pump relay turns off and the fuel pump is powered by the oil pressure sending unit. If the vehicle’s computer is unable to keep the fuel pump relay running throughout the starting process, the vehicle may start and quit immediately after starting.

  • Ignition Coil: Your vehicle’s ignition coil takes the low voltage of the battery and provides the thousands of volts needed to create a spark in the spark plugs. When an ignition coil begins to fail, it may struggle to provide consistent spark to the plugs, causing the engine to stall after starting.

What to expect:

A top-rated mobile mechanic will come to your home or office to determine the reason why the vehicle starts and then dies. The mechanic will then provide a detailed inspection report outlining why the vehicle quit and the cost of any repairs that need to be made.

How it's done:

A mechanic will begin diagnosing your vehicle’s issue by plugging a code reader/scanner into the vehicle’s computer. The mechanic should be able to get more information from your vehicle’s computer on what component has failed. Using this information, the mechanic can begin necessary repairs.

If your vehicle has a bad or failing mass airflow sensor, the mechanic will begin by finding the sensor in the engine bay and checking for any signs of failure. The mechanic should check the wire harness connected to the sensor to ensure that all of wires are properly connected. After removing the sensor, the mechanic should be able to discover the nature of the failure and replace the sensor.

If the mechanic suspects an issue with the fuel pump relay, he or she should check the vehicle’s computer for a problem. If the vehicle’s computer is having difficulty providing consistent power to the fuel pump relay, the computer may need to be reprogrammed or replaced. If the vehicle’s computer is functioning normally, the mechanic may need to replace the fuel pump relay.

If the mechanic suspects that the ignition coil may be faulty, he or she should first disconnect the battery before beginning work. The mechanic should then begin the process of disconnecting wires from the ignition coil and removing it from the engine bay. The mechanic will then install the new ignition coil and ensure that it is connected properly. The mechanic should then reconnect the battery and test the new coil.

With all repairs, the mechanic will ensure the newly installed parts work properly. The mechanic can then turn off and warning lights that may have come on while the vehicle was not running properly.

How important is this service?

If your vehicle is starting but dying soon after starting, you should have it checked out by a mechanic. Issues involving the fuel management and electrical systems will become worse if not dealt with. Diligence and paying attention to warning lights may help prevent further damage to critical engine component and may save money in repairs. A vehicle that quits after starting can be inconvenient and having a mobile mechanic inspect and repair you vehicle will ensure that you and your vehicle are back on the road soon.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0

Jason

32 years of experience
534 reviews
Jason
32 years of experience
Chevrolet Bolt EV Electric - ABS Speed Sensor Replacement (Driver Side Front) - San Mateo, California
Nice guy. Competent.

Andre

16 years of experience
48 reviews
Andre
16 years of experience
Chevrolet Bolt EV Electric - Pre-purchase Car Inspection - Laurel, Maryland
He was on time communication in HIGH level very nice and very professional

Tien

23 years of experience
903 reviews
Tien
23 years of experience
Chevrolet Bolt EV Electric - Tire Rotation - Berkeley, California
Tien provides expert service. He's efficient, helpful and communicates well. 10 out of 10!

Pierre

9 years of experience
317 reviews
Pierre
9 years of experience
Chevrolet Bolt EV Electric - Pre-purchase Car Inspection - Roslindale, Massachusetts
Pierre was a real professional. On-time, clear communication, performed a thorough pre-purchase inspection, and documented his findings. Would definitely reach out to Pierre for future needs!

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0
Number of Chevrolet Bolt EV services completed
55+
services done by our mechanics
TOTAL NUMBER OF EXPERT Chevrolet MECHANICS
1600+
experts on our platform

Recent articles & questions

How to Register a Car in Texas
There There are a number of benefits that come with moving to Texas. When you first arrive in the Lonestar state, you will need to take the time to ensure that you are on the right side of the law....
P2197 OBD-II Trouble Code: O2 Sensor Signal Stuck Lean Bank 2 Sensor 1
P2197 code definition O2 Sensor Signal Stuck Lean Bank 2 Sensor 1 What the P2197 code means This code is usually an...
How Much Does a Mechanic Make in Connecticut?
Automotive technician jobs in Connecticut have an mean salary of $40k, with some mechanics earning as much as $43k.

Issues with the unlocking doors using a remote

Try to use another remote to see if the problem happens still with that remote. Sometimes the remote button sticks and only holding the button will allow the other buttons to work. If another remote is being used, make sure...

Caliper sticking

Hello. This is not usually a common problem, however, it is possible and can happen for a variety of unforeseen reasons. Usually when a caliper sticks it is a result of a misaligned caliper (https://www.yourmechanic.com/services/brake-caliper-replacement) or potentially a wheel bearing...

There was a swift sportz manual car but the problem is its steering getting heavy

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com