BMW 318i Front Crankshaft Seal Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

customer ratings

(21)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

customer ratings

(21)

Front Crankshaft Seal Replacement Estimate for BMW 318i

BMW 318i Front Crankshaft Seal Replacement costs $421 on average.

CarServiceEstimateShop/Dealer Price
1985 BMW 318iL4-1.8LService typeFront Crankshaft Seal ReplacementEstimate$445.58Shop/Dealer Price$565.99 - $679.15
1984 BMW 318iL4-1.8LService typeFront Crankshaft Seal ReplacementEstimate$400.58Shop/Dealer Price$508.53 - $612.35
Show example BMW 318i Front Crankshaft Seal Replacement prices

Front Crankshaft Seal Replacement Service

What is the Front Crankshaft Seal all about?

A number of mechanisms must work together to make your vehicle move forward. One of the most important is the crankshaft, which converts rotary into linear motion; i.e., it transforms the force created by the engine's pistons moving up and down into a force that moves in a circular motion that causes a car’s wheel to turn. Enclosed in what’s called a crankcase—the largest cavity in the engine block, just below the cylinders—the crankshaft must be completely lubricated, essentially submerged in oil, to spin nearly friction-free and do its job properly.

Consequently, there are seals located at either end of the crankshaft that allow it to spin freely and keep engine oil from escaping the engine block, as well as prevent contaminants and other debris from entering and causing damage to the mechanism. Since there are two ends of the crankshaft, there are two types of seals: the front crankshaft seal and the rear crankshaft seal, also known as the front main and rear main seals.

Keep in mind:

  • Loss of oil will eventually cause serious internal engine damage.
  • Inspect the sealing surface of the crankshaft or the crankshaft pulley (depending on the engine design) for damage when replacing the crankshaft seal.
  • Oil degrades rubber components.

How it's done:

  • The vehicle is raised and supported on jack stands
  • The crankshaft damper and timing belt is removed
  • The crankshaft seal is removed and a new one installed
  • The timing belt and cover along with crankshaft damper is reinstalled
  • The engine accessory belts are installed and the vehicle is lowered off of the jack stands

Our recommendation:

One of the most important parts of your car, crankshaft seals are typically made from a durable material, such as a synthetic rubber or silicone, designed to handle the extreme pressure and temperatures as well as the caustic chemicals in your engine oil. Because they are exposed to such abuse, main seals are subject to a lot of wear and tear. And whether you are talking a front or rear main seal, replacement is the only cure when one malfunctions.

The good news is that the seals are relatively inexpensive components. The bad news is that neither is easy to replace.

Front seal: The front seal is located behind the main pulley that drives all the belts, which is, of course, always spinning. The main pulley throws any leaking oil out in a big circle. It can get thrown up on the alternator, steering pump, belts, in short anything attached to the front of the engine and cause a real mess and eventually some serious damage. Consequently, it has to be removed along with many of the components attached to the front of the block to replace the front main seal.

Rear seal: The rear crankshaft seal is placed along with the transmission; therefore, the process of replacing it requires the removal of transmission, as well as the clutch and flywheel assembly. This is a very involved job.

What common symptoms indicate you may need to replace the Front Crankshaft Seal?

  • Oil leaking from the front crank pulley.
  • Oil dripping from the bottom of the clutch housing, where the block and transmission meet.
  • Clutch slip caused by oil spraying on the clutch.

How important is this service?

Letting either crankshaft seal continue to leak can be detrimental to your vehicle’s continued operation. Besides the maladies caused by driving around with little to no oil flowing in the engine, the faulty seal will be spread oil through the engine bay and undercarriage of your car as you drive, a mess that is difficult to clean up and can be a fire hazard. Replacing is better addressed sooner than later.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(21)

Rating Summary
20
0
1
0
0
20
0
1
0
0

Firas

21 years of experience
11 reviews
Firas
21 years of experience
BMW 318i L4-1.8L - Throttle Position Sensor - San Leandro, California

Richard

11 years of experience
450 reviews
Richard
11 years of experience
BMW 318i L4-1.8L - Clutch Slave Cylinder - Washington, District of Columbia
Great experience all around -- highly recommend.

Michael

27 years of experience
95 reviews
Michael
27 years of experience
BMW 318i L4-1.9L - Oil Change - Houston, Texas
First time using this service and had a great experience. Michael was professional, knowledgeable, and got the job done in a timely fashion. Would definitely use this service again.

Mark

11 years of experience
349 reviews
Mark
11 years of experience
BMW 318i L4-1.8L - Brakes, Steering and Suspension Inspection - Saratoga, California
Mark was awesome!

Excellent Rating

(21)

Rating Summary
20
0
1
0
0
20
0
1
0
0
Number of BMW 318i services completed
231+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1100+
experts on our platform

Recent articles & questions

P0345 OBD-II Trouble Code: Camshaft Position Sensor A Circuit Malfunction (Bank 2)
Trouble code P0345 means the computer has detected an incorrect voltage reading from the bank 2 camshaft position sensor.
B2110 OBD-II Trouble Code: Front Wiper Motor Relay Circuit Open
B2110 trouble code means there's an error in the front wiper motor relay circuit, caused by a faulty front wiper relay or electrical components.
Essential Things to Know About the Toyota Prius Hybrid Car
The Toyota Prius first came out in 1997. The current Prius gets 58 miles per gallon and can travel a mile without any gas when it's in EV mode.

2011 CAMRY LE 2.5 NOISE WHEN GOING STRAIGHT AND GOES AWAY WHEN TURNING RIGHT OR MERELY MOVING STEERING TO RIGHT. SOUNDED LIKE A WH

If wheel bearings are installed without using a calibrated torque wrench to apply the hub axle nut to the exact required torque specification, the bearings are more or less instantly destroyed once you start driving on them. This, indeed, is...

Will a 2010 camaro transmission fit in a1999 chevy van 1500

Hi there. There is an old saying in mechanics - "with fabrication, everything is possible". However, compatibility with modern technology is an entirely different subject. The transmission from a 2010 Camaro has multiple sensors and electrical solenoids that would most...

How much does it roughly cost to fix the p0304 code on a 2000 gmc Jimmy

Hi there. The cost of the repair would depend on the problem that is causing the misfire on the #4 cylinder. It can be as simple as needing a new spark plug to as expensive as an engine rebuild if...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com