Suzuki Reno Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(16)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(16)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Suzuki Reno Tie Rod End Replacement is $134 with $39 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2005 Suzuki RenoL4-2.0LService typeTie Rod End - Front Left Inner ReplacementEstimate$271.08Shop/Dealer Price$308.86 - $386.19
2008 Suzuki RenoL4-2.0LService typeTie Rod End - Front Right Inner ReplacementEstimate$239.08Shop/Dealer Price$276.89 - $354.24
2008 Suzuki RenoL4-2.0LService typeTie Rod End - Front Left Inner ReplacementEstimate$239.08Shop/Dealer Price$276.89 - $354.23
2007 Suzuki RenoL4-2.0LService typeTie Rod End - Front Left Outer ReplacementEstimate$187.35Shop/Dealer Price$220.44 - $297.20
2006 Suzuki RenoL4-2.0LService typeTie Rod End - Rear Left Outer ReplacementEstimate$187.35Shop/Dealer Price$220.47 - $297.27
2008 Suzuki RenoL4-2.0LService typeTie Rod End - Rear Right Outer ReplacementEstimate$172.19Shop/Dealer Price$201.51 - $266.92
2008 Suzuki RenoL4-2.0LService typeTie Rod End - Front Right Outer ReplacementEstimate$177.19Shop/Dealer Price$206.37 - $271.68
2007 Suzuki RenoL4-2.0LService typeTie Rod End - Front Right Outer ReplacementEstimate$177.19Shop/Dealer Price$206.74 - $272.34
Show example Suzuki Reno Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Suzuki mechanics

Real customer reviews from Suzuki owners like you.

Excellent Rating

(16)

Rating Summary
16
0
0
0
0
16
0
0
0
0

Johnnie

29 years of experience
35 reviews
Johnnie
29 years of experience
Suzuki Reno L4-2.0L - Oil Change - Clayton, North Carolina
Very helpful, and even pointed brought things to my attention that will need to be fixed in the near future. I plan to do further business with Mr. Johnnie.

Breck

20 years of experience
681 reviews
Breck
20 years of experience
Suzuki Reno L4-2.0L - Car is not starting - Houston, Texas
Quick And Very Efficient 10/10

Theodore

16 years of experience
1601 reviews
Theodore
16 years of experience
Suzuki Reno L4-2.0L - Clutch Slave Cylinder - Seattle, Washington

Jonathan

22 years of experience
304 reviews
Jonathan
22 years of experience
Suzuki Reno L4-2.0L - radiator hose clamp - Denver, Colorado
super professional and straight forward

Excellent Rating

(16)

Rating Summary
16
0
0
0
0
16
0
0
0
0
Number of Suzuki Reno services completed
176+
services done by our mechanics
TOTAL NUMBER OF EXPERT Suzuki MECHANICS
300+
experts on our platform

Recent articles & questions

How to Keep Your Car Door Hinges from Squeaking
Like any other metallic component, car door hinges need lubrication. The door hinge, door check, and rubber seal are common sources for door noise.
How to Select an Auto Broker
Using Using an auto broker can save you time and effort when looking for a new or used vehicle. Alternately known as car brokers, motor brokers, or a car-buying service, auto brokers search for a vehicle for you and work...
How to Find a Cosigner for a Car Loan
If If you are just starting your career or if your credit scores have fallen below an acceptable point, getting loans for large items like a car or a house can seem nearly impossible. Companies do not want to sell...

Transmission

Odds are that something inside the transmission has failed. If for instance the front pump has failed, there will be no hydraulic pressure within the transmission. Automatic transmissions rely on that hydraulic pressure to move as well as shift up...

P0300

You will need to have the engine fuel pressure and injectors checked to see if the pressure is low and if okay then the fuel injectors may need cleaned. This can cause the problem you are having.

I have an Mercury Sable 2001 and when I put my car in reverse it goes forward. I have a leak but I don’t know where it’s coming

Assuming the vehicle has an automatic transmission, there is a park or neutral switch on the transmission that impacts the functioning of the shift solenoids within the transmission. When this is not working properly, this may cause the vehicle to...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com