Ram C/V Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(9)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(9)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Ram C/V Tie Rod End Replacement is $175 with $71 for parts and $104 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2013 Ram C/VV6-3.6LService typeTie Rod End - Front Left Outer ReplacementEstimate$267.91Shop/Dealer Price$314.27 - $428.58
2012 Ram C/VV6-3.6LService typeTie Rod End - Front Right Outer ReplacementEstimate$245.91Shop/Dealer Price$292.29 - $406.62
2014 Ram C/VV6-3.6LService typeTie Rod End - Rear Left Inner ReplacementEstimate$305.31Shop/Dealer Price$366.53 - $525.41
2012 Ram C/VV6-3.6LService typeTie Rod End - Front Left Outer ReplacementEstimate$245.91Shop/Dealer Price$292.26 - $406.57
2012 Ram C/VV6-3.6LService typeTie Rod End - Front Right Inner ReplacementEstimate$305.31Shop/Dealer Price$366.55 - $525.44
2015 Ram C/VV6-3.6LService typeTie Rod End - Rear Left Inner ReplacementEstimate$305.31Shop/Dealer Price$366.53 - $525.41
2012 Ram C/VV6-3.6LService typeTie Rod End - Rear Left Inner ReplacementEstimate$310.81Shop/Dealer Price$371.88 - $530.65
2014 Ram C/VV6-3.6LService typeTie Rod End - Rear Left Outer ReplacementEstimate$251.41Shop/Dealer Price$298.04 - $412.57
Show example Ram C/V Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ram mechanics

Real customer reviews from Ram owners like you.

Excellent Rating

(9)

Rating Summary
9
0
0
0
0
9
0
0
0
0

Chris

15 years of experience
312 reviews
Chris
15 years of experience
Ram C/V V6-3.6L - Alternator - Spring Valley, California
Chris did a great job! He was on time and even early which he text me to see if it was ok and I was thrilled to get the work done earlier! I will use your service again!!! Thank you!

Chris

22 years of experience
2229 reviews
Chris
22 years of experience
Ram C/V V6-3.6L - Oil Change - Irvine, California
It's really hard to schedule an appointment with a dealership and they always seem to have a delay. I was blown away by everything including a few automotive tips. We're going to have him service our other cars. Another great thing is now I can be preventative and know when and how long I will be without my work vehicle.

Jamie

22 years of experience
94 reviews
Jamie
22 years of experience
Ram C/V V6-3.6L - Thermostat Housing - Moreno Valley, California
Had a great experience with Jamie, he showed up and got the job done.

Duane

25 years of experience
510 reviews
Duane
25 years of experience
Ram C/V V6-3.6L - Brake System Flush - Spring Valley, California
Dwane was very professional. I have not driven my car yet, but I am sure the work will be outstanding.

Excellent Rating

(9)

Rating Summary
9
0
0
0
0
9
0
0
0
0
Number of Ram C/V services completed
99+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ram MECHANICS
300+
experts on our platform

Recent articles & questions

Veteran and Military Driver Laws and Benefits in Oregon
The The state of Oregon offers a number of benefits and perks for those Americans who have either served in an Armed Forces branch in the past, or are current active military members. License and registration tax and fee exemption...
How to Sell a Classic Car
Selling Selling classic and collector cars is rarely about finding a buyer as much as it is finding the right price. Because classic and collector cars are highly sought after, you have to make sure you’re making a good deal...
How to Get Kia Dealership Certified
Kia car dealerships offer automotive technician jobs to mechanics who are Kia certified through an accredited Kia training school like Kia University.

How do I replace the remote keyless entry (RKE) transmitter battery of a 2012 Dodge Ram?

The remote keyless entry (RKE) transmitter battery should last for at least three years. After three years, there’s a chance that it will die and need to be replaced. Replacing the RKE transmitter battery takes four steps. Buy a replacement...

Trouble code P0133 - 2002 Dodge Durango

Do you know if there are any exhaust leaks before the sensor? This code trips when the O2 sensor is not switching back an forth between rich and lean as fast as the computer is setting the conditions. This can...

Smaller serpentine belt shredded and pieces went into the crank shaft Tried to start timing jumped. How do I fix? 05' kia op 2.4L

The KIA 2.4 liter motor is what is called an interference motor and this means it will bend valves if the timing belt breaks or jumps timing. You will need to have cylinder head removed and bent valves replaced if...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com