Nissan LEAF Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(8)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(8)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Nissan LEAF Brake Drum Replacement is $341 with $208 for parts and $133 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2012 Nissan LEAFElectricService typeBrake Drum ReplacementEstimate$653.11Shop/Dealer Price$790.14 - $1169.73
2011 Nissan LEAFElectricService typeBrake Drum ReplacementEstimate$823.41Shop/Dealer Price$1010.04 - $1538.37
2019 Nissan LEAFElectricService typeBrake Drum ReplacementEstimate$577.70Shop/Dealer Price$698.79 - $1023.73
2014 Nissan LEAFElectricService typeBrake Drum ReplacementEstimate$625.11Shop/Dealer Price$762.13 - $1141.71
2018 Nissan LEAFElectricService typeBrake Drum ReplacementEstimate$577.70Shop/Dealer Price$698.82 - $1023.77
2016 Nissan LEAFElectricService typeBrake Drum ReplacementEstimate$549.21Shop/Dealer Price$667.29 - $989.97
2013 Nissan LEAFElectricService typeBrake Drum ReplacementEstimate$632.11Shop/Dealer Price$768.97 - $1148.44
2015 Nissan LEAFElectricService typeBrake Drum ReplacementEstimate$556.21Shop/Dealer Price$674.62 - $997.55
Show example Nissan LEAF Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Nissan mechanics

Real customer reviews from Nissan owners like you.

Excellent Rating

(8)

Rating Summary
7
0
0
0
1
7
0
0
0
1

Patrick

15 years of experience
406 reviews
Patrick
15 years of experience
Nissan Sentra L4-1.8L - Brake Drum - Highland Springs, Virginia
Great service and very professional. Job was done quick and precise !!

Charles

17 years of experience
176 reviews
Charles
17 years of experience
Nissan Sentra L4-1.8L - Brake Drum - San Carlos, California
Prompt, efficient and did a great job. Thanks Charles!

William

33 years of experience
69 reviews
William
33 years of experience
Nissan Sentra L4-1.8L - Brake Drum - Murrieta, California
Work completed as requested. Recommend!*****

Javier

9 years of experience
10 reviews
Javier
9 years of experience
Nissan Murano V6-3.5L - Brake Drum - Moreno Valley, California
Timely, fast and negotiable

Excellent Rating

(8)

Rating Summary
7
0
0
0
1
7
0
0
0
1
Number of Nissan Brake Drum Replacement services completed
88+
services done by our mechanics
TOTAL NUMBER OF EXPERT Nissan MECHANICS
1500+
experts on our platform

Recent articles & questions

P0056 OBD-II Trouble Code: HO2S Heater Control Circuit (Bank 2 Sensor 2)
P0056 P0056 trouble code definition The P0056 trouble code signifies that there is a problem with the heater control circuit in the bank 2 sensor 2 oxygen sensor. What the P0056 code means This code means that the bank 2...
Disabled Driver Laws and Permits in New Jersey
In In the state of New Jersey, the Motor Vehicle Commission (MVC) provides parking permits and plates to drivers who have disabilities. If you have a disability, whether it is permanent or temporary, you can get a permit that will...
How to Claim Your New Car as Tax Deductible
When you buy a new car, you’ll likely finance (https://www.yourmechanic.com/article/what-s-the-cheapest-way-to-finance-buying-a-car) a large portion of your purchase. Very few people can pay for the whole amount up front. Unless you are able to obtain 0% interest on your vehicle loan, your...

Head gasket blown

Hi there. Common signs of a blown head gasket are: overheating, thick white smoke from the tail pipe, milky liquid in the oil cap or radiator cap, or loss of coolant. If you need assistance with an inspection or replacement...

Car Vibrating and bottoming out

The basic condition of the engine can be verified through a cylinder compression test. If the compression in each cylinder is within factory spec., there is not too much variance across cylinders, and you are not using more than a...

Engine light came on Ford my Ford explorer the coded are c1440 p0732 p0735 p0775 and p1000 what are those and what do they mean?

Hi Bryant. Thanks for contacting us today. On our website, we have a rather large amount of articles on OBD-II trouble codes. If you click the blue links on the specific codes, you can read about them. P0732 (https://www.yourmechanic.com/article/p0732-obd-ii-trouble-code-p0732-gear-2-incorrect-ratio-by-valerie-johnston), P-0735...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com