Land Rover Freelander Front Crankshaft Seal Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(11)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(11)

Front Crankshaft Seal Replacement Service

How much does a Front Crankshaft Seal Replacement cost?

On average, the cost for a Land Rover Freelander Front Crankshaft Seal Replacement is $1185 with $577 for parts and $608 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2005 Land Rover FreelanderV6-2.5LService typeFront Crankshaft Seal ReplacementEstimate$1890.58Shop/Dealer Price$2291.25 - $3241.25
2003 Land Rover FreelanderV6-2.5LService typeFront Crankshaft Seal ReplacementEstimate$1762.58Shop/Dealer Price$2163.45 - $3113.59
2004 Land Rover FreelanderV6-2.5LService typeFront Crankshaft Seal ReplacementEstimate$1762.58Shop/Dealer Price$2163.43 - $3113.56
2002 Land Rover FreelanderV6-2.5LService typeFront Crankshaft Seal ReplacementEstimate$1762.58Shop/Dealer Price$2163.18 - $3113.12
Show example Land Rover Freelander Front Crankshaft Seal Replacement prices

What is the Front Crankshaft Seal all about?

A number of mechanisms must work together to make your vehicle move forward. One of the most important is the crankshaft, which converts rotary into linear motion; i.e., it transforms the force created by the engine's pistons moving up and down into a force that moves in a circular motion that causes a car’s wheel to turn. Enclosed in what’s called a crankcase—the largest cavity in the engine block, just below the cylinders—the crankshaft must be completely lubricated, essentially submerged in oil, to spin nearly friction-free and do its job properly.

Consequently, there are seals located at either end of the crankshaft that allow it to spin freely and keep engine oil from escaping the engine block, as well as prevent contaminants and other debris from entering and causing damage to the mechanism. Since there are two ends of the crankshaft, there are two types of seals: the front crankshaft seal and the rear crankshaft seal, also known as the front main and rear main seals.

Keep in mind:

  • Loss of oil will eventually cause serious internal engine damage.
  • Inspect the sealing surface of the crankshaft or the crankshaft pulley (depending on the engine design) for damage when replacing the crankshaft seal.
  • Oil degrades rubber components.

How it's done:

  • The vehicle is raised and supported on jack stands
  • The crankshaft damper and timing belt is removed
  • The crankshaft seal is removed and a new one installed
  • The timing belt and cover along with crankshaft damper is reinstalled
  • The engine accessory belts are installed and the vehicle is lowered off of the jack stands

Our recommendation:

One of the most important parts of your car, crankshaft seals are typically made from a durable material, such as a synthetic rubber or silicone, designed to handle the extreme pressure and temperatures as well as the caustic chemicals in your engine oil. Because they are exposed to such abuse, main seals are subject to a lot of wear and tear. And whether you are talking a front or rear main seal, replacement is the only cure when one malfunctions.

The good news is that the seals are relatively inexpensive components. The bad news is that neither is easy to replace.

Front seal: The front seal is located behind the main pulley that drives all the belts, which is, of course, always spinning. The main pulley throws any leaking oil out in a big circle. It can get thrown up on the alternator, steering pump, belts, in short anything attached to the front of the engine and cause a real mess and eventually some serious damage. Consequently, it has to be removed along with many of the components attached to the front of the block to replace the front main seal.

Rear seal: The rear crankshaft seal is placed along with the transmission; therefore, the process of replacing it requires the removal of transmission, as well as the clutch and flywheel assembly. This is a very involved job.

What common symptoms indicate you may need to replace the Front Crankshaft Seal?

  • Oil leaking from the front crank pulley.
  • Oil dripping from the bottom of the clutch housing, where the block and transmission meet.
  • Clutch slip caused by oil spraying on the clutch.

How important is this service?

Letting either crankshaft seal continue to leak can be detrimental to your vehicle’s continued operation. Besides the maladies caused by driving around with little to no oil flowing in the engine, the faulty seal will be spread oil through the engine bay and undercarriage of your car as you drive, a mess that is difficult to clean up and can be a fire hazard. Replacing is better addressed sooner than later.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Land Rover mechanics

Real customer reviews from Land Rover owners like you.

Excellent Rating

(11)

Rating Summary
9
2
0
0
0
9
2
0
0
0

Chris

16 years of experience
47 reviews
Chris
16 years of experience
Land Rover Freelander V6-2.5L - Car is not starting - Pleasanton, California
Very positive

Manuel

32 years of experience
580 reviews
Manuel
32 years of experience
Land Rover Freelander V6-2.5L - Crankshaft Position Sensor Replacement - Irvine, California
Highly recommendable. On time and very courteous.

Michael

37 years of experience
39 reviews
Michael
37 years of experience
Land Rover Freelander V6-2.5L - Radiator Hose Repair - Hayward, California
Michael was very punctual and professional. He worked very efficiently with my car, which is not an easy thing to do. He was very knowledgeable with getting my car done on time. With owning a freelander, most mechanics would not touch my car, but Michael tackled the job without any hesitation. Thank you for a great job.

Robert

12 years of experience
125 reviews
Robert
12 years of experience
Land Rover Freelander V6-2.5L - Oil Change - Clarksburg, Maryland
Robert is very respectful and skilled.

Excellent Rating

(11)

Rating Summary
9
2
0
0
0
9
2
0
0
0
Number of Land Rover Freelander services completed
121+
services done by our mechanics
TOTAL NUMBER OF EXPERT Land Rover MECHANICS
500+
experts on our platform

Recent articles & questions

How to Buy a Good Quality Windshield Washer Pump
You You rely on your windshield washer wipers to clear away all the dirt, slush, grime, rain, and snow. Sometimes a simple wipe isn’t enough, and this is why you turn to your windshield washer pump to provide the cleaning...
P2118 OBD-II Trouble Code: Throttle Actuator Control Motor Current Range/Performance
P2118 code definition The P2118 code is a general OBD-II diagnostic trouble code (DTC) that is referencing the throttle actuator control motor...
P2700 OBD-II Trouble Code: Transmission Friction Element "A" Apply Time Range/Performance
P2700 means the transmission friction element application needs attention, possibly because of a leak in the transmission or defective pump.

With the air on or off my car hesitates at take off and going up any size hill and will not go over 40 in my 2002 Pontiac Bonneville

It is possible that you could have an issue with your crankshaft or camshaft position sensor. Fuel issues may also be the cause of your symptom. It is very likely that trouble codes were stored in your vehicle's powertrain control...

I have a 2013 Acura Ilx. When I push button on handle on drivers side it no longer beeps and locks.

Hello. This is a programming issue within the door locking system. The programming can become corrupted and cause this. You will need to take the vehicle to the dealer in order to get it reprogrammed.

2007 Mazda 3 manual transmission when putting get into here one two four and five work three does not but once you get it into like second gear it starts to rock or jerk you back and forth kind of like almost like a bunny hop what is causing it

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com