Ford F-250 HD Distributor Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(11)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(11)

Distributor Replacement Service

How much does a Distributor Replacement cost?

On average, the cost for a Ford F-250 HD Distributor Replacement is $278 with $174 for parts and $104 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1997 Ford F-250 HDV8-5.8LService typeDistributor ReplacementEstimate$474.03Shop/Dealer Price$571.92 - $840.82
Show example Ford F-250 HD Distributor Replacement prices

What is a distributor and how does it work?

The distributor is an electro-mechanical component installed in a car’s ignition system to provide, time, and “distribute” the spark that occurs at each spark plug in an engine’s combustion cylinders. The distributor contains a rotating shaft with a gear at the bottom that engages a gear on the engine’s camshaft. Atop the shaft is a plastic rotor that has electrical contacts molded in. As the plastic rotor turns, it completes a high voltage circuit to each electrical contact, one per engine cylinder, that is molded into a plastic distributor cap. That high voltage then flows along the spark plug wire to the spark plug, creating the spark that ignites the air-fuel mixture in an engine cylinder.

Distributors vary in design: some may have the ignition coil built in, some have vacuum advance mechanisms attached for engine timing, and really old distributors may even have mechanical points. Vintage cars, that is cars older than 25 years, will more commonly be equipped with a distributor. Most modern car designs have replaced the distributor with fully electronic systems controlled by engine sensors for more precise, and more powerful, ignition system operation.

When to consider replacing the distributor:

  • Worn or damaged integral parts. Worn shaft bushings can result in wobbling or eccentric rotation of the rotor, resulting in misfires, loss of power, rough idle and poor mileage. If the shear pin breaks that secures the distributor shaft drive gear, complete loss of ignition spark distribution is the result. A failed ignition module that is mounted to the distributor housing may also be more cost-performance efficient to replace the entire distributor.
  • Visible oil leaks. Distributors are attached to the engine and consequently, there are seals, both internal and external, that keep oil from leaking at the point of attachment. External O-rings are serviceable but if an internal oil leak occurs, due to a worn shaft, for example, it might necessitate rebuilding or replacing the distributor.

How do mechanics replace the distributor?

Distributors are bolted to the engine block or the cylinder head. The replacement procedure is as follows:

  • Once all diagnostic tests are complete and the distributor is confirmed to be faulty, disconnect the battery negative cable.
  • Set engine at top dead center on the compression stroke for cylinder no. 1. Mark location of distributor housing and shaft relative to the engine mounting surface.
  • Remove primary and secondary ignition system wiring connected to the distributor. Unbolt and remove the distributor. Temporarily cover the hole in the head or block so no foreign matter drops into the engine.
  • Install new distributor and new cap and rotor, with the rotor pointing to the cylinder no. 1 firing-order electrode of the distributor cap. Reconnect all wiring and reconnect battery negative cable.
  • Start engine and set basic engine ignition timing per original equipment manager specification. Then check timing advance for proper function. Road test vehicle.

Is it safe to drive with a distributor problem?

Yes. A faulty distributor will cause increased fuel consumption, increased emissions and poor engine operation but does not generally create a safety hazard.

When replacing a distributor keep in mind:

  • Many ignition system failures will mimic a distributor failure, including faulty spark plugs, faulty wiring, and a worn cap and rotor. Mechanics will always test the distributor directly to ensure it is not needlessly replaced.
  • If a distributor is removed for testing and then re-installed, be sure that new o-rings are installed. Re-using old o-rings often results in oil leaks.
  • If the distributor is replaced, and the spark plugs and spark plug wires have considerable mileage on them, the best results will be obtained by replacing those components at the same time the new distributor is installed.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(11)

Rating Summary
9
1
0
0
1
9
1
0
0
1

Excellent Rating

(11)

Rating Summary
9
1
0
0
1
9
1
0
0
1
Number of Ford F-250 HD services completed
121+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1700+
experts on our platform

Recent articles & questions

Symptoms of a Bad or Failing Power Steering Pump
If you hear squealing noises, the steering wheel feels stiff, or find damage on the power steering belt, have the power steering pump replaced.
How to Replace a Brake Hose
Modern Modern cars use a combination of metal lines and rubber hoses to contain and transfer the fluid that applies your brakes. The lines coming out of the brake master cylinder are made of metal to be strong and long...
Windshield Laws in New York
If If you are a licensed driver in New York, you know you are required to follow numerous traffic laws when navigating the roadways. While those rules are designed to keep yourself and others safe, there are also rules governing...

Thermostat

The cooling system would need to be completely checked out to see if the cooling fan circuit is working correct. If the fans are not coming on it would allow the engine to overheat. The thermostat would cause the engine...

Car occasionally won't start. Is it the starter?

Hello. If the alternator is working and the battery is new, as you say, then the mechanic may be right. The starter itself may not be dead so much as it would be that the solenoid is sticking. When that...

Temperature gauge goes up slightly then back to normal

If you are not running the a/c system at the time you see the temperature gauge go above the middle of gauge and back down every few minutes then this is normal cycling of the cooling fan. If you turn...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com